My Orders
ARG7302 Amana Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
top burners would not light
2 of 2 people
found this instruction helpful.
-
neil from foxboro, MA
- Easy
- 15 - 30 mins
-
Screw drivers
Removed the top, 4 screws and pulled the contact wires off. Replaced the module and connected the contacts. Put back the screws and the top. When the stove was new it did not operate properly and we had a technician out, but naturally it worked for him. For the past 14 years intermittent operation has been agravating me. With the new m
... Read more
odule the burners have never worked so well.
Read less
Was this helpful?
Thank you for voting!
Burners wouldn't light
2 of 2 people
found this instruction helpful.
-
Robert from Ottawa, IL
- Really Easy
- 15 - 30 mins
-
Screw drivers
Unscrewed the burners,lifted the top up,unplugged the burners.Took out the bad module,making sure of where the wires went and put them in the same spots on the new module,reconnected the burners lowered the top screwed the burners back in and the burners lit.
Was this helpful?
Thank you for voting!
Broiler Would Not Turn On
3 of 5 people
found this instruction helpful.
-
William from Lake Zurich, IL
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
Un plug elect. Cord. Remove door by pulling upward removed back stove panel, un did 2 wire nuts leading to igniter. Un screw igniter inside oven at top next to burner pad. Interchanged old ignitor with new plug stove back in. Thats it.
Was this helpful?
Thank you for voting!
ignintion spark was very weak, burners would not light
3 of 6 people
found this instruction helpful.
-
marv from Eugene, OR
- Really Easy
- 15 - 30 mins
-
Screw drivers
removed two screws from each burner, removed ignitor wires from burners, pulled range top removed old module and inserted new reattaching wires for four burners, switch and power to new module. reset top, attached wires to burners and reinserted screws
Was this helpful?
Thank you for voting!
Missing oven rack
2 of 3 people
found this instruction helpful.
-
Denise from Pittsburgh, PA
- Really Easy
- Less than 15 mins
Although this was not a repair I wanted to let you know your service was outstanding and the price quite reasonable. I am very happy to finally have a much needed second rack in my oven that was not there when I purchased my home. Thank You
Was this helpful?
Thank you for voting!
end cap deformed from heat
2 of 3 people
found this instruction helpful.
-
Richard from Lincoln, RI
- Easy
- Less than 15 mins
-
Screw drivers
Removed 3 screws, lifted the top control panel. Adapted new plastic end panel and replaced new end cap an refastened with original screws.
Was this helpful?
Thank you for voting!
Broiler inoperative
2 of 3 people
found this instruction helpful.
-
Donald from East Syracuse, NY
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
For the third time in less than a year I had to replace the broiler igniter. The range is 27 years old and has given us excellent service. When the igniter failed it's replacement lasted 3 months. The next replacement lasted about 6 months. This last replacement has been in service about 1 week. We shall see. The last one had an open wire
... Read more
within the ceramic mould. There was continuity from one wire, through the black portion, but not to the second wire. It seems like it was a fault in manufacturing.
Read less
Was this helpful?
Thank you for voting!
Gas cooktop burners would not light
2 of 4 people
found this instruction helpful.
-
Bruce from Lake Oswego, OR
- Easy
- 30 - 60 mins
-
Screw drivers
We lived with the problem by using a long-reach butane torch lighter for three years after an appliance repairman told us the problem would be very costly to repair. Finally, we found the likely suspect when we happened onto PartSelect's website- the spark ignition module. The cost was just over $81 plus shipping. We ordered on Wednesday,
... Read more
it arrived on Friday by FedEx, and I installed it on Saturday morning. All the parts were included, the instructions were clear and complete, and, best of all, our range now works as it should. We couldn't be happier. Thanks, PartSelect.
Read less
Was this helpful?
Thank you for voting!
no ignition at burners
2 of 4 people
found this instruction helpful.
-
Carroll from Lynden, WA
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Removed burners and top cover to access ignition module.
Remove and replace module and reassemble stove.
Remove and replace module and reassemble stove.
Was this helpful?
Thank you for voting!
Oven wouldn't heat
1 person
found this instruction helpful.
-
Timothy from Madison, AL
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable)
WEB research indicated that even though ignitor would glow, that it was likely faulty.
Turned off power at circuit breaker
Remove shelves and bottom plate from inside oven.
Unscrew deflector plate
Remove drawer under stove
Remove ignitor and unplug from connector
replace ignitor, plug in, reassemble stove. ... Read more r />Needed flashlight to see under stove.
Turned off power at circuit breaker
Remove shelves and bottom plate from inside oven.
Unscrew deflector plate
Remove drawer under stove
Remove ignitor and unplug from connector
replace ignitor, plug in, reassemble stove. ... Read more r />Needed flashlight to see under stove.
Read less
Was this helpful?
Thank you for voting!
Oven doesn't start
1 person
found this instruction helpful.
-
Dennis from STEWARTVILLE, MN
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Installed new igniter - easy job. Remove burner deflector, remove screws holding igniter bracket, remove panels below oven (accessible via removal of drawer), disconnect igniter and remove. Remove igniter from bracket, slide new one into bracket and reverse the steps to install it. Unfortunately, it didn't work. Igniter not glowing.
... Read more
I checked continuity on the igniter and it showed 90ohms resistance, so seems to be OK. Put multimeter on range plug end, turned on oven and multimeter did show cycling voltage at the plug (although I'm not certain what it should read). Relay in the control board does 'click' when oven turned on, so it also seems to work. Think I may be down to the gas control safety valve for the oven, but it is no longer available. Anyone have any other ideas? Hate to buy another igniter and have it still not work. Thanks!!
Read less
Was this helpful?
Thank you for voting!
old igniter would not light stove
1 person
found this instruction helpful.
-
Carlos from EAST NEWARK, NJ
- Really Easy
- 30 - 60 mins
Ceramic connectors were taken off the old igniter, pulled off old igniter and replaced in the same way the new igniter
Was this helpful?
Thank you for voting!
NO Work.
1 person
found this instruction helpful.
-
Robert J. from WESTMINSTER, MD
- Very Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Followed Instructions with part. Easy Install. However the problem not solved. I believe Oven Control defective (Worn Out). Replacement May not be available. Still looking. Thank You. RJC
Was this helpful?
Thank you for voting!
Oven would not light, even though the ignitor looked as though it was working, the slightest crack affects the resistence and the signal to send gas does not work.
1 person
found this instruction helpful.
-
WILLIAM from BENSALEM, PA
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
It was Tuesday before thanksgiving, panic as there was a big bird looking for a hot stove,
unplug stove from its electrical supply
turn off gas, not necessary but sometimes it's good to be safe.
inside oven remove bottom splash cover "pull towards you and lift out, then remove flame pan, one nut in the center, remove and l ... Read more ift out flame pan.
The oven ignitor was to the left of the burner, with 3 philips screws one attached to buner and the other two to the back of the stove, remove all three.
The ignitor is now loose,
remove bottom drawer and behind is a plate attched to the back of the stove with two screw, the screws are facing you as you look in where the drawer was, remove screws and plate to access the plug attatching the ignitor to its power supply .
go back to the oven and remove ignitor.
install new, feed plug through back, and put it all back together.
"ignitor very delicate, handle with care"
I am also not the biggest of guys and it can be awkward getting in the drawer space as you need both hands to plug it back in, so tilting the stove back, keeping safety in your thoughts at all times, would be a must for most people.
unplug stove from its electrical supply
turn off gas, not necessary but sometimes it's good to be safe.
inside oven remove bottom splash cover "pull towards you and lift out, then remove flame pan, one nut in the center, remove and l ... Read more ift out flame pan.
The oven ignitor was to the left of the burner, with 3 philips screws one attached to buner and the other two to the back of the stove, remove all three.
The ignitor is now loose,
remove bottom drawer and behind is a plate attched to the back of the stove with two screw, the screws are facing you as you look in where the drawer was, remove screws and plate to access the plug attatching the ignitor to its power supply .
go back to the oven and remove ignitor.
install new, feed plug through back, and put it all back together.
"ignitor very delicate, handle with care"
I am also not the biggest of guys and it can be awkward getting in the drawer space as you need both hands to plug it back in, so tilting the stove back, keeping safety in your thoughts at all times, would be a must for most people.
Read less
Was this helpful?
Thank you for voting!
Our oven was very slow lighting (would sometimes take over 30 minutes)
1 person
found this instruction helpful.
-
Richard from Greenville, NC
- Easy
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
The repair was fairly simple. The hardest part was figuring out the best way to get access to the part. Basically just had to remove the cover at the bottom of the oven then remove the shield that was directing the heat that comes off of the burner. Once I had access to that, I could see the ignitor. To get access to the plug in secti
... Read more
on, I had to take out the bottom drawer for pots and pans, then remove the piece above that to get access to the place that the ignitor plugs into. Unfortunately the wires were too short, but so were the ones that were on the current ignitor so I used the extension from the existing ignitor and cut off the plug of the new one to attach the extension. Once that was done, just reinstalled the ignitor and we reversed the process. The new one works incredibly well. Instead of waiting several minutes for the oven to start heating up, it heats up instantly. What a relief...much cheaper than buying a brand new stove. This one works great now!! Thank you parts select!!
Read less
Was this helpful?
Thank you for voting!