AMV6 - Parts

If your microwave is not turning on it could be due to your fuse needing to be replaced. This part protects the microwave by shutting it off if there is an electrical surge. This fuse is just over an inch long, is metallic on both ends and ceramic in the middle. Before beginning this repair, unplug the appliance and wait a few minutes bef...Read moreore starting. Remove the outer cabinet which is held in place with two screws. You will then locate the power cord which will lead you to the fuse holder. Determine if the fuse has blown. Using an ohmmeter, you should be able to figure out if it has blown. A proper reading is zero ohms, if it reads as anything else then your fuse has in fact blown. Simply snap the old fuse out of place and place the new one in.

This is an authentic LG charcoal filter for your microwave, sourced directly from the manufacturer. It is designed to remove odors from the air that circulate through your microwave vent. It measures approximately 11 inches in length, and 2.5 inches in width.

The light socket in your microwave houses the light bulb and connects it to the power source. The light bulb will screw into it, so the light bulb will be held in place. Be very careful when installing this part, and be sure to consult your manual before you begin this repair.

The turntable tray rotates in the centre of the microwave to help ensure the food cooks evenly.

This glass tray drive coupling, also known as a tray support, is a genuine OEM replacement part. It can help solve the issue of your microwave tray not turning properly. This motor couple connects the motor to the turntable. To replace this part, make sure the microwave is unplugged first. Remove the glass tray, and the existing coupling. Insert the new coupling into the motor shaft.

Sold individually.

This is a microwave air filter that is located on the bottom side of an over-the-range appliance. No tools are needed for this repair, simply pull back on the tab to lift the existing filter out, and replace with new filter. This air filter is eight inches long, 5 inches tall, and is made entirely of metal. This is an OEM part that is sou...Read morerced from the authentic manufacturer of the appliance. To preserve the life of your microwave air filter, occasionally take it out and wash it in a warm water and detergent solution.

This damper is an authentic OEM replacement assembly used in microwave/range hood combos. It includes the damper door and frame. It is designed to direct the flow of air through the vent duct, and the release of steam and heat from the appliance during cooking. Over time, the damper door and frame can wear down or become obstructed by foo...Read mored particles and debris. A faulty damper assembly will result in poor ventilation, uneven cooking, and excessive moisture buildup which can damage internal components in the appliance. Disconnect any wires or connectors attached to the faulty damper assembly and remove it from the appliance. Position the new damper assembly and reconnect the wires/connectors before securing it with the appropriate fasteners.

This top interlock support is a genuine OEM safety component designed for microwave ovens. It plays a critical role in ensuring the appliance operates only when the door is securely closed, preventing potential radiation exposure. The support holds the interlock switch in place and provides a reliable latching point, allowing the microwav...Read moree to function safely and efficiently. A faulty or misaligned support may result in the microwave failing to start, operating with the door ajar, or displaying error codes related to the door lock system. Replacing this part restores proper door engagement and ensures safe operation. Installation may require disassembling the control panel and should be performed with the appliance unplugged.

Also known as a switch holder.

This bracket holds the metal or plastic flapper that closes off the exhaust duct when the fan is not running and opens when the fan turns on. If the exhaust fan on your microwave does not appear to be working, the problem may be with the damper assembly. If the damper does not open and close easily, check for any damage to the bracket, an...Read mored replace if it is damaged or faulty. This genuine OEM exhaust damper measures approximately 12 inches long by 5 inches wide.

This door switch, also known as a safety switch, is a genuine OEM replacement part for microwaves. It is a safety mechanism that sends signals to the microwaves control system, telling it when the door is open/closed. This ensures that the microwave only operates when the door is securely shut and switches off as soon as the door is open....Read more Over time, this switch can become worn out or damaged. A faulty door switch can result in failure to switch the microwave on/off, lack of heat, and running with the door open. To confirm that the door switch is faulty, use a multimeter to test for electrical failure. To remove the faulty switch, disconnect the wiring connectors and take note of where they are positioned. Place the new switch in position and reattach the wiring connectors to the appropriate terminals and close the microwave door to check that the switch engages appropriately.