ALW9 Amana Washer - Instructions

remove front cover disconnect water supply remove hose clamp,take drain line replace with new hose reconnect water supply replace front cover job complete.

Disassembled washer as per directions with seal kit. Removed inner tub. Cut both tub shaft bearing in half; punched out from outter tub. Installed new bearings using .5 inch threaded rod, washer and bolts. Installed new seal on inner tub shaft. Installed inner tube. Re-assembled washer.

Since the agitator and bell housing seperated as once piece from the drive shaft I didn't have to remove them and the schematic showed how the agitator snapped on to the bell housing and the parts I needed for the fix. The new seal went on with no problem, I just used some of the supplied grease on the tight spots. The hardest part w ... Read more as attaching the bell housing. It came to within an inch of the top of the shaft with no problem with a rubber hammer. But the top screw shroud broke when I tried to hammer it the rest of the way using a wood dowel and a block of wood. I couldn't even get the threads of the supplied screw to even touch the drive shaft. So I bought a longer (1 inch) cap screw from the hardware store and added a washer and suplied ring. After torqing it to 5 ft-lbs instead of the 10-20 the plastic beneath the screw was looking kind of thin and stressed and I was afraid of it breaking through or the screw snapping off in the shaft, so I left it alone and used some silicone caulk to seal in the plug that goes in on top of the screw since the side of the shroud broke off. I slipped on the agitator and am testing a load now as we speak. If I get ten more years out of the washer it will definitely be worth the $100 in parts and shipping !

The hardest part was removing the tub from washer by myself. I simply removed the bolts holding the sides to the bottom of the unit and lifted it straight off. Be careful when you remove the springs from the drum so they don't spring back and puncture the drain line. Thank you RTV gasket maker. Once the drum was free from the base, i tilt ... Read more ed the drum back exposing the pump housing. I used a pair of pliers to remove both drain lines then removed the 3 hex screws freeing the pump. I had no problem removing it from the motor shaft, it slipped right off. I put everything back together as easily as it came apart.

Removed old hose, drained the water from the hose. Put new hose on.

Repair went well using posted instructions. My advice is always replace pump as you will damage seal when pulling pump off shaft.

knife to losen top, remove rear tabs securing top, unplug electical from timer and switches, unplug front door wiring, 2 bolts remove front, lift front pannel to remove. tape belt on drum on top. under drum you can see the belt around worn pulley. lift idler pulley assembly, remove belt from pulley, snap ring holds pulley in place remove ... Read more woren pulley, install new, replace snap ring, restring belt. remove tape. spin drum to assure alignment. reassemble.

Removed the tension spring from the belt retention belt, removed the belt from the large pulley in the back of the washer, removed the 4 bolts holding in the motor and washer pump, removed wiring harness, disconnected the inlet and outlet hoses from the pump and pulled out the motor and the washer pump. Turned the motor over and using the ... Read more Torx driver (#20) removed the 3 bolts holding on the pump. Gently wiggled and pried the washer pump off of the motor, replaced the pump and tightened down the Torx bolts carefully so the pump didn't crack or break it is just plastic, but had to be sure the pump was seated tightly so the pump would fit back into place and also so it wouldn't leak, after making sure it was tightly attached I reversed the process to put it back together.

Although the Maytag website no longer had a repair manual in their database, I was able to locate one fairly easily online. After removing the motor/washer pump, it was easy to remove the 3 screws holding the washer pump to the motor. Unfortunately, it turned out the motor hub shaft had corroded and removing the pump needed some ... per ... Read more suasion. Patience and a rubber mallet eventually separated the water pump from the motor. Re-installing went quickly and, so far, no leaks and the washing machine has not started walking across the floor.

The new hose was exactly like the one I removed. It was simply a matter of putting the new hose through the back, replacing the hose clamp, take the piece off the old hose that makes the bend in the hose to go in the wall drain. Replace the lower front panel with two screws and I was done.

Purchased x4 new adjustable legs. Leaned the washer back and held in place with block of wood. Loosened the two older front legs with an adjustable wrench because they had a locking nut and replaced with new legs. Repeated process on back side of washer. Once all the new legs were installed leveled the machine adjusting the legs if nec ... Read more essary.

remove motor and pump togather 4 bolts holding unhook two hose unplug electrial connector and slide out remove 3 screws holding pump to motor be aware of direction belt from moter to tub then place new pump back at same location as old pump replace motor with pump attached back to same location as begfor

You tubed this procedure and it took 20 min.

Laid washer back on a appliance dolly, removed the front cover, checked to see if the hose was touching the motor mount (it was). Removed the drain hose from the pump and standoffs, removed the hose and disk from the back of the washer that holds the hose. Replaced the hose on the pump, turn the standoff to move the hose farther from the ... Read more motor mount, and install it in the disk. May be easier to measure the hose and do the disk first as it is not easy to get the hose bent when it is installed first on the pump.

My neighbor did the repair for me and I believe the instructions sent were the reason he had no trouble installing it.