AHS - Overview

This Primer Bulb is a clear, plastic, individually sold part with an Outer Diameter of 0.720 inches (18.30 mm) and a Height of 0.674 inches (17.12 mm). With Flange: 0.842" (21.40 mm). This part is rated as Easy to install by customers, and attaches to the primer pump assembly. If the part shows signs of breakage, such as cracks appearin...Read moreg due to the bulb drying out, or fatigue, then it must be replaced. Refer to your owners manual/model number to ensure you are choosing the correct part.

The Primer Pump, aka the Pump Bulb, is a clear, individually sold, plastic part, sourced from the original equipment manufacturer. It has an Outer Diameter of 0.616 Inches, 15.66mm and is 0.558 Inches and 14.19mm in height. This part is used to pump fuel from the tank to the carburator and is rated Easy to install. This part installs on...Read moreto the primer assembly. If the part dries out or starts leaking that means it is broken (likely due to fatigue or general wear) and must be replaced. Check the model number to ensure you are choosing the right part.

The fuel return tube or fuel return line, as it is also known, delivers fuel back to the tank from the primer bulb. This is a genuine OEM part from the manufacturer, and it is yellow in color and sold individually. Its overall dimensions are 3x6x90mm. Over time, or due to over-tightening, cracks may appear in your fuel return tube, causin...Read moreg fuel to leak. You will know it is time to replace this part if you notice these symptoms. This is an easy repair, according to our customers, and does not require any special tools. The new part will simply attach to the primer bulb and fuel tank.

This a a genuine OEM replacement check valve for your small engine. It is also known as a fuel tank vent. You may need to replace this part if you are noticing debris or dirty oil in the reservoir. Make sure the engine is cool before you begin this repair, and remove the wire and boot from the spark plug to prevent the engine from starting up.

Safe window mounting depends on hardware that supports the air conditioner and closes the open spaces around it. Bent brackets, torn seals, or broken side panels can cause noise, air leaks, and poor alignment. Inspect the window and existing mounting points before replacing the kit. Match every piece to the full appliance model, since kit...Read more contents may vary. Disconnect power, have a helper hold the unit during installation, and fasten it to a sound structure rather than relying on the window sash alone.

This OEM Nut is a silver, metal, individually sold part. It can be installed using a wrench or socket by torquing to the manufacturer specifications. This part may become damaged over time due to fatigue, which will result in damaged threads or rounded off edges. If damaged it should be replaced. Check your owners manual to see if this...Read more is the correct part for you, as this part can be applicable to a long list of equipment. The difficulty of this part installation varies depending on its application, but it genuinely should be an easy repair.

This OEM Fuel Filter is a white and silver, steel part, sold individually. It requires a pair of pliers to install and is ranked as Easy to repair by our customers. This part attaches inside of the fuel tank, and is used to clean the fuel of debris. This part should be changed regularly as part of good engine maintenance. If the engine ...Read moresounds like it is not getting enough fuel or is underperforming, remove the filter to heck for a blockage. If there is a blockage or the part is leaking, then it likely needs a replacement.

Also referred to as a Spark Arrester, this Spark Arrester Screen is an authentic OEM replacement part that is not part of a kit or assembly. It is made of metal and sold individually. The purpose of this screen is to prevent flammable debris from entering the engine and becomes worn through regular use. If the screen is clogged, remove th...Read moree screen from the muffler, hold it with pliers, and use a torch to burn off the debris before reinstalling the screen. This part needs to be replaced when it becomes damaged or worn. When the screen is malfunctioning, you may notice debris exiting through the muffler. To complete this repair, you will need a screwdriver and pliers. This screen is located within the muffler; refer to your owner's manual for the exact location on your model. Customers rated this repair as Easy.