AHS262 (U00415001001-U00415999999) Shindaiwa Hedge Trimmer - Overview

The Primer Pump, aka the Pump Bulb, is a clear, individually sold, plastic part, sourced from the original equipment manufacturer. It has an Outer Diameter of 0.616 Inches, 15.66mm and is 0.558 Inches and 14.19mm in height. This part is used to pump fuel from the tank to the carburator and is rated Easy to install. This part installs on...Read moreto the primer assembly. If the part dries out or starts leaking that means it is broken (likely due to fatigue or general wear) and must be replaced. Check the model number to ensure you are choosing the right part.

The fuel return tube or fuel return line, as it is also known, delivers fuel back to the tank from the primer bulb. This is a genuine OEM part from the manufacturer, and it is yellow in color and sold individually. Its overall dimensions are 3x6x90mm. Over time, or due to over-tightening, cracks may appear in your fuel return tube, causin...Read moreg fuel to leak. You will know it is time to replace this part if you notice these symptoms. This is an easy repair, according to our customers, and does not require any special tools. The new part will simply attach to the primer bulb and fuel tank.

This a a genuine OEM replacement check valve for your small engine. It is also known as a fuel tank vent. You may need to replace this part if you are noticing debris or dirty oil in the reservoir. Make sure the engine is cool before you begin this repair, and remove the wire and boot from the spark plug to prevent the engine from starting up.

Also referred to as a Spark Arrester, this Spark Arrester Screen is an authentic OEM replacement part that is not part of a kit or assembly. It is made of metal and sold individually. The purpose of this screen is to prevent flammable debris from entering the engine and becomes worn through regular use. If the screen is clogged, remove th...Read moree screen from the muffler, hold it with pliers, and use a torch to burn off the debris before reinstalling the screen. This part needs to be replaced when it becomes damaged or worn. When the screen is malfunctioning, you may notice debris exiting through the muffler. To complete this repair, you will need a screwdriver and pliers. This screen is located within the muffler; refer to your owner's manual for the exact location on your model. Customers rated this repair as Easy.

Used in over 150 models of outdoor power equipment, this clip is commonly used to clip fuel lines or other hoses/tubes in place. It is sold individually, not as part of a kit or assembly, made of metal, and is silver in color. When this clip becomes damaged or worn, it can no longer support the fuel line, which may cause a fuel leak and...Read more/or smell. This wear will occur as part of regular use of your equipment. To complete this repair, you will need a wrench, screwdriver, and pliers. It is found in a variety of locations depending on your model; please refer to your owners manual for the exact location. Customers rated this repair as Easy.

This OEM nut is a 5mm, gold, metal nut, which is sold individually. It can be installed with a Wrench or Socket and Torque Wrench by torquing to the manufacturer specifications. This nut is used to secure another part in place, and should be replaced if damaged due to fatigue (such as damaged threads or rounded ends). This nut can have v...Read morearious uses on various equipment, and as such the difficulty of the installation can vary, but generally this is an easy repair.

This oil seal is an OEM part that is used in trimmers, blowers, and edgers made by Shindaiwa and Echo. This item is a part of the small block assembly and is used to prevent oil leaks from between the crankshaft and the crankcase. The oil seal is priced individually, please note that two seals might be required.

This OEM metal washer is commonly used on a variety of different small engine/lawn equipment models and is sold individually. This washer is used to help evenly distribute pressure from the securing bolt or screw with the cylinder cover, to reduce any effects of vibration from the engine. If the connection between the securing fastener be...Read morecomes loose, or if you are replacing the fastener itself, it is recommended that you replace this washer as well.

This is a genuine Echo replacement part that has been sourced from the original manufacturer to be used with trimmers. The stopper is used to support the flexible liner to limit vibration inside the main pipe assembly. The stopper is sold as an individual replacement part, please note two stoppers may be needed.

This is an authentic Echo replacement part, sourced from the original manufacturer for use with hedge trimmers. The special torx head screw is commonly used to fasten the gearcase cover. This screw is available as an individual replacement part, please see model diagram for associative parts.

It is a genuine OEM approved replacement item specially designed for use with Echo gas powered handheld tools. This replacement fuel-strainer/filter fits inside of the fuel tank. The purpose of this item is to filter out dirt and debris from contaminating engines. Over time fuel filter will get clogged and restrict the fuel getting to the...Read more carburetor. At this point filter should be replaced. This filter consists of a metal body with fabric filter material and it is sold individually.

Also refered to as a Collar, this part is sourced directly from the manufacturer for use with lawn and garden equipment. The collar fits between the top guard and the engine cover. It is sold individually, it is not part of a kit or an assembly. It is made of durable black plastic and can become worn with regular use. The exact location...Read more varies from model to model; refer to your owners manual to determine the location on your machine. No tools are required to complete this repair, and it should be replaced when it is missing or damaged. Customers rated this repair as easy.