AGS74 Amana Range - Instructions

Removed burner with attached igniter assembly by raising forward legs from slots and pulling unit from rear support. Note: this is contrary to instruction #1 on installation instructions. Then followed the remaining instuctions 2 - 7 as written. Everything worked as planned.

I ordered new racks to see if they weere out of alignment. The new racks fell from its tracks after the broiler was heated. It seems the oven cabinet is expanding with the heat and the rack width does not compensate for that. The new racks did not solve the problem so I do not know what can be done next. Any shelf support would have to be ... Read more heat resistent. Replacing the oven cabinet is not a good option and no gauantee it wouldn't continue with this stove.

I bought the part and replaced it.

Very simple process of just ensuring you have the correct size racks and remove the old racks and replace them with the new ones.
Having ordered a lot of things on the internet, I am very pleased with using Part select and would "highly" recommend them to all!!

Bought a new one. . Three years later =)

I just replaced the racks with beautiful, new, shiny racks. My wife was very pleased

First turned off power to oven, Took burner out by lifting up and pulling out, then pulled out wires attached to the oven and igniter, removed two wire nuts and disconnected the wires then removed burner assembly from oven. With screwdriver and nut driver removed old igniter from housing and put new one in place, tightened up screws carr ... Read more ied back to oven reattached wires with wirenuts and feed wires back into oven, then put burner back carefully silding igniter into hole in back of oven. Turned power back on to oven and worked nice. Took all of 15 mins to complete.

ordered new broiler pan

shut off gas at tank, pulled stove out from counter area to gain acess to back, removed oven door removed removed screws holding igniter unit in place, i then removed the stove rear panel to get at the wiring for ignitor,remoded old part returned to front and installed new part, checked voltage then re-connected new wires, turded gas back ... Read more on and tested oven, oven came on less than a minute, put rear panel on stove put door back on and put stove back into counter area, stove works like new.

Unplugged the stove, removed all 4 burner discs from the stove top (2 screws each- WATCH YOU DONT STRIP HEADS) and disconnecting electrode wires ( DONT HAVE TO- IF YOU HAVE ENOUGH ROOM TO SIDE TOP UNIT OVER), unscrewed the old module, removed each of the 6 wires,one at a time and connected wires to the new module. Plug in stove to test be ... Read more fore you screwed it into place, reinstalled the top unit , put the stove top in place,. Done!

remove knobs and 2 screws from front panel, remove front panel. remove burner grates and caps. remove 8 screws (2 per burner base). remove each base and unplug wire. remove the top of the range. locate an remove old ingition module with bracket. on my model i did not need the new bracket. the new module fit right in the old one. unplug w ... Read more ires from old module and plug them into the new one in the same place they were in the old one. reverse the order to reassemble. new module does not make the same clikcing noise (not as fast as old one), but it lights on the first click. GRERT JOB PARTSELECT.!!! parts go to my house within 2 days...saved about $40-$50.

The first one came damaged and customer service credited the first one and got another on the way the same day. They were awesome to deal with. I removed the oven racks, the burner cover, the storage drawr, and the door. That took about 5 minutes. I removed 3 screws that held the ignitor in place. I removed the 2 wire nuts from the wires ... Read more in the drawr space. I slid the ingitor cover off the old ignitor and onto the new one. Slid the new ignitor into place and fed the wires below and put on the 2 wire nuts, then installed the 3 screws and tested the operation. I put the oven back together and put the tools away. Total time about 20 minutes.

found igniter not working, pulled up on door and it came off, lifted up bottom of oven and pulled out, removed wing nut on deflector to access igniter, removed igniter retaining bolts, unplugged connector, be careful not to let connector slip back in stove, and reverse process to install new igniter,, all took about twenty minutes, easy ... Read more repair,

The repair was quite easy. Remove the two screws and put in the new part. The only problem I had was the hinge sent was the wrong side (but it still worked) and the new hinge had no threads for the screws. I had to tap the holes so that the screws could be used.

Took the pan out of the bottom of the oven. Took the screws out of the assembly for the iron, disconnect the power wires under the stove and pull out the old iron. Reverse the proceedure but be careful with the new iron, it is very fragile. Connect the wires put the screws back and you are done. Make sure before you start the job that yo ... Read more u unplug the appliance !!!!