AFC2 Amana - Instructions

Unpacked, inspected, found two minor defects in the form of two tiny slivers along the seal edge which I cut with a small scissor, laid the seal down on the kitchen table, applied heat to the deformed areas and reshaped them with my fingers, heated the entire seal lightly, removed the old seal starting at the right hand upper corner using ... Read more my fingers, installed the warm seal starting at the top corners by pushing it in its slot making sure the outer lip stayed out of the slot and worked my way around. I believe that the heat from the dryer made it pliable and easier to manage.

Turn water and refrigerator off, use hair to thaw the ice maker filler tube, then remove the filler tube inside the freezer. Next remove the water supply line cover plate in back of the refrigerator. Now remove the speed clip at the white pvc elbow and pull out the supply line. Next, grasp the pvc elbow with pliers and pull hard to rem ... Read more ove. The new filler tube is a 1 piece design (filler tube and elbow combined) and needs to be cut to the proper length. Mark it inside the freezer, remove it and cut to length. Now coat the outside flange with caulk or PU glue and snap into the opening. Put the speed clip on the elbow first and center it. Ensure that the spreader insert is in place in the plastic tube, then slide the supply line into the elbow untill completely engaged. Replace cover.

I opened the freezer door and peeled out the freezer gasket, inserted the new gasket, and closed the door. I repeated this same process for each of the French doors on the refrigerator. This was very easy to do. The only issue is the replacement gaskets don't seem to have any better stick or magnetic hold than the original gaskets, so I'm ... Read more not sure the repair will improve the energy efficiency / performance of the appliance.

Pushed the hinge pins aside and removed the old lid.. Reversed the process to install the new lid

Pantry Cover:

I just slided out the tray, and unscrewed the left pantry panel that was broken, and replaced it with the new one, then put in the new cover after sliding the trays back in.

Ice Maker:

I unplugged the power connector in the back, unscrewed the ice maker with a flat screw driver (3 screws), s ... Read more lide it out, and then unplugged the wiring from the old ice maker and put it into the new one, mounted the new ice maker back in, make sure the lever is working, and then closed the freezer to let it cool down so that water can start flowing to it when it becomes cold enough (took about a good hour or so before water started filling the ice maker). Once the freezer was cold enough, water started filling the ice maker, and it begin making ice again.

First I removed the Ice bin, I then loosened the ice bin rail under the ice maker and removed the screw that attached the bottom of the ice maker to the side of the fridge. I unplugged the power to Ice Maker from the back of the fridge and unscreewed the two screws that secured the ice maker to the fridge. This allowed the Ice Maker to ... Read more be removed from the fridge. To replace the new ice maker I simply repeated the steps in reverse.

Philips head screwdriver and ten minutes was all it took! I removed the two screws that hold the icemaker assembly in place, then pulled it out a little and disconnected the electrical plug freeing the icemaker assembly. Then I snapped the external parts off my old icemaker assembly and snapped them on the new icemaker assembly. Installin ... Read more g the new icemaker assembly was just as fast and easy. I snapped the electrical plug into the new icemaker assembly, then screwed in the two screws. It was making ice shortly thereafter. Glob free ice! I'm glad I didn't call a repairman. I probably saved a hundred bucks. A ten year old could accomplish this simple and easy task. No wonder the Maytag repairman has time on his hands.

Found the coils in the freezer frosted up and no cold air getting to the refrig compartment. I first replaced the defrost timer but should have checked with a volt meter as it turned out that it was a thermostat on the coils in the freezer that was faulty, it actually had a visable defect, it was bulged out. I think that this thermostat ... Read more prevents the defrost heater from over heating the coils. Replaced the defrost timer an this thermostat and all is good now.

I pulled the whole unit(condenser&overload relay)
with my hand & disconnected the wire connected
to it & Replaced it with the new one.Peace of cake.

The new Ice Maker Assembly arived in less than 24 hours. I was amazed that it came so fast.

I had already removed the old ice maker in order to get the modle number.

I just took two parts off of the old ice maker and quickly snapped them into place on the new ice maker. Then attached it to the refrigerator i ... Read more n less than 10 minutes. With in a few hours I had ice again !!!!!

I would definatly use partselect.com again.

First, I removed the drawers at the bottom of the fridge and then I removed the three hex head (7/32) screws that hold the end cap on. Then I disengaged the slider which connects to the temperature control for the pantry drawer. Then, unscrewed the drawer slides with a Phillips from the old end cap. Also the slide push rod has to be di ... Read more sengaged from the clips on the back of the endcap.

Then, I reinserted the push rod to the new end cap and reattached the drawer sliders and the slider itself. At this point I realized I SHOULD have unscrewed the temperature slider at the back where it covers the cold air outlet. The screw had slipped out. I replaced it with a slightly larger wood screw. Reinstall the drawers, all done.

Freezer would get cold at bottom and some of the refrigerator. Took of freezer back panel and located freezer fan. Took a meter and saw power was getting to it, but not working. Removed fan and replaced with new on, working like a charm. Cold air was not circulating enough throughout the unit because fan was not working. It was not t ... Read more he thermostat or adapter control.

Popped out old gasket and popped in nwe one. This is where things get interersting, the new gasket
Does work as well as the one I replaced. I think the maganet is not strong enough. If anyone has had the same problem please let me know. This model ( Maytag- French door ) has been a lemon.

This is the 2nd part I have bought for this refrigerator from Part Select. I wish the parts came with some kind of instruction. I had to re-use parts from the original equipment each time. After studying the replacement part I was able to figure out what I needed to do, but it would have been nice to have a little more information. Th ... Read more ere were 3 pieces which I needed to remove from the damaged piece and add to the replacement part. I would gladly pay more for a complete replacement part.

Replacement of freezer door handle.
1. Removed freezer door handle. First I read the freezer door handle removal instructions in the Amana refrigerator user guide. Removing the handle requires inserting a plastic card at least 1.5 inches under the left end of the right side of the handle so it releases the butterfly clip latch on t ... Read more he freezer door. Next I pulled the right side of the handle to lift it away from the freezer door. Then still holding the handle away from the door, at the spot that is 1.5 inches from the inside of the right side of the handle, I held the plastic card vertically and slid one corner of it between the handle and the freezer door and worked the card down until it released the butterfly clip latch. Keeping the card at the same space under the handle so the latch was released, I then turned the card to the left until it was horizontal and was lifting the left end of the right door handle away from the freezer door. I then slid the handle across the card to the left until it cleared both door butterfly clip latches and it lifted off the door.
2. Installed freezer door handle. First I read the freezer door handle installation instructions in the Amana refrigerator user guide. The handle is curved on one edge and must be installed the curved side down. Correctly installed, the outside ends of the handle curve upward and the handle curve is down so it looks like a frowning mouth. Next holding the handle curved edge down, I turned it up so I could see the brackets and held it against the door. I lined up the handle brackets slightly to the left of the butterfly clips on the freezer door. Next I turned the handle with the brackets against the freezer door and slid it slightly to the right until the left side of the handle held onto the door butterfly clip by itself but was not latched. Then I lined up the right handle bracket with the right freezer door butterfly clip and carefully slid the whole handle to the right until I heard the left butterfly clip latch click. Next I slid the handle back slightly left once more and then slid it back to the right until I heard the right butterfly clip latch click.