backout one screw, push mullion up and free from upper and lower slotted tabs, disconnect one electrical connector. Reverse the steps to reinstall. Literally took 2 minutes.
in stalled new circuit board an thermostat an was fixed
Was this helpful?
Thank you for voting!
Refrig. was not holding proper temp in refrig compartment
2 of 2 peoplefound this instruction helpful.
Dan from Goldens Bridge, NY
A Bit Difficult
15 - 30 mins
Remove light lens by pushing straight back (needs some oomph, but not too much). Remove control housing by prying spring clips in back of housing with thin screwdriver or knife. Remove old control board by releasing plastic clips on both sections and removing 2 wiring plugs. Be careful snapping new control board in ; the alignment of the
... Read more4 switches and the 2 readouts is critical - easy to hang up a switch. Snap the control housing back into place, making sure that it is all the way in. Position the light lens so that it is lined up and about 1/2" back and then slide it forward (toward you) into place. The instruction sheet calls the refrigerator section the "fresh food" section. There are 2 light switches, one for each door. Both have to held down to get light to go out and enter programming mode. Easiest to close the right door, then push left door switch and quickly push the freezer DOWN button 3 times. Follow the instructions to set the program on the display and then push AND HOLD the freezer DOWN button until the display starts flashing. Release the freezer DOWN button, close the doors, open the doors to check. Display will indicate two 4s. (that was what mine indicated). Done.
Read less
Was this helpful?
Thank you for voting!
Refrigerator would stop cooling intermittently, control panel would not display temp settings until power was reset.
2 of 2 peoplefound this instruction helpful.
Jim from HALTOM CITY, TX
Easy
15 - 30 mins
Screw drivers
The video on the part select website with the Canadian gentleman was absolutely the best! My wife and I watched it and was able to accomplish the replacement with no surprises or issues. One tip that we could add is that the orientation of the temperature sensor was not specified in the video, but the slot seemed to work better for one or
... Read moreientation versus another. It has been a couple weeks since the repair and the refrigerator is working like it did when we first purchased it.
Read less
Was this helpful?
Thank you for voting!
The old shelf shattered when we tried to clean it
2 of 2 peoplefound this instruction helpful.
Michael from COAL VALLEY, IL
Easy
30 - 60 mins
Just slipped it in. I think it's a very poor design.
Was this helpful?
Thank you for voting!
My refrigerator vegetable bins were sagging when I placed veggies in it.
2 of 2 peoplefound this instruction helpful.
Lee from SAMMAMISH, WA
Easy
30 - 60 mins
Screw drivers
I came across this site and looked at the diagrams. Instead of buying a new crisper bin frame, I noticed that the crisper bin frame was missing the frame brace. I purchased the frame brace and installed it in the crisper frame, which was easy to push into the slot. This solved my problem. No more sag!!
Was this helpful?
Thank you for voting!
Refrigerator was warm,freezer was cold
2 of 2 peoplefound this instruction helpful.
Henning from RHINELANDER, WI
A Bit Difficult
30 - 60 mins
Screw drivers, Wrench (Adjustable)
Unplugged refrigerator,cleaned out freezer.Removed shelves in freezer compartment(that took some figuring to unlock sliding sheves)Our freezer is on the bottom.Removed four screws from back cover to expose fan,removed screws and attached wires.Carefully opened plastic clips after pulling fan off shaft.Replaced old motor after reattachin
... Read moreg rubber seals.Closed clips to hold motor and placed fan back on shaft.Reattach wires and screws. Put cover back and replaced shelves.Plugged in refrigerator and wallah refrigerator part was cold again!
Read less
Was this helpful?
Thank you for voting!
the freezer and refrigerator number would lower it self and eventually get to "-" and "-" essentially shutting it self off!!
2 of 2 peoplefound this instruction helpful.
Marc from SEASIDE, CA
A Bit Difficult
30 - 60 mins
Screw drivers
I replaced the Control Board... the two boards need to be installed first . than plug in the connectors (refrigerator was unplugged of course.!) i plugged in the connectors first. and had to disconnect them. install the boards first. than plug in the electrical connectors.. strange for a day or two it still did not work proper
... Read morely and than one day. it started working ok 7 on the freezer and 3 on the refrigerator. I do not know why..
Read less
Was this helpful?
Thank you for voting!
Rear mount tab broken on Center Crisper Rail
2 of 2 peoplefound this instruction helpful.
Joseph from Live Oak, FL
Really Easy
Less than 15 mins
It took longer to empty the glass shelf above the Crisper Bins than to replace the rail. Since the part simply snaps in place, no tools were required
Was this helpful?
Thank you for voting!
Light switch broke.
2 of 3 peoplefound this instruction helpful.
Mike from New Johnsonville, TN
Really Easy
Less than 15 mins
Couldn't figure out how to get the old one out till I saw the new one.Pop the old one out slide the 2 wires on the new one pop it back in place,good to go.
Was this helpful?
Thank you for voting!
Light switch on door broke
3 of 6 peoplefound this instruction helpful.
Donna from Oro Valley, AZ
Really Easy
Less than 15 mins
Popped out broken switch with blunt flat edged instrument. Disconnected switch from unit . Plugged new piece in and reinserted into side panel of refrigerator. Very easy.
Was this helpful?
Thank you for voting!
Light switch broke
2 of 3 peoplefound this instruction helpful.
Matthew from Pensacola, FL
Easy
Less than 15 mins
Screw drivers
Popped out the old light switch with a butter knife from the bottom first, disconnected the plug in. Install was just the reverse. Super easy fix
Was this helpful?
Thank you for voting!
The door switch was broken so the interior light would not come on.
2 of 3 peoplefound this instruction helpful.
Catherine from BROOMALL, PA
Easy
Less than 15 mins
Screw drivers
The instructions in the package were not helpful. They wanted me to cut the wiring harness and described where to cut based on the wire colors. My wires were not the same color! I removed the light mechanism using a combination of a screwdriver, putty knife, and plain old muscle with my fingers! The wiring harness unplugged easily and th
... Read moree new one inserted. It was easy to push the whole assembly back into the door. I spent more time looking for something to cut the wiring harness with (and never did find it) than the whole job actually took without needing to cut anything!
My Orders
