Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Center Crisper rail
3 of 4 peoplefound this instruction helpful.
Richard from PASADENA, CA
Really Easy
Less than 15 mins
Take everything off the top self, lift the self install the new part ,put self back in place and then install the drawers again. Took minutes.
Was this helpful?
Thank you for voting!
I purchased a display model that was missing a part.
3 of 4 peoplefound this instruction helpful.
Monte from Longview, WA
Really Easy
Less than 15 mins
Snapped on the new toe grille.
Was this helpful?
Thank you for voting!
broke my original Kickplate Grille
3 of 4 peoplefound this instruction helpful.
Daniel from GEORGETOWN, TX
Really Easy
Less than 15 mins
knelt down, positioned replacement kickplate; popped into place, stood up!
took longer to open the box and peel bubble wrap off item than to replace it!
Was this helpful?
Thank you for voting!
did not have a ice maker
5 of 10 peoplefound this instruction helpful.
Ralph from Argenta, IL
Really Easy
More than 2 hours
Nutdriver, Pliers, Screw drivers, Wrench set
remove parts that were not need installed water valve , ice maker unit and hooked up water supply tested and it works fine. got the parts really quick Thank You
Was this helpful?
Thank you for voting!
ICE BUILD UP AT BOTTOM OF FREEZER
3 of 5 peoplefound this instruction helpful.
Gerald from COLORADO SPGS, CO
Really Easy
30 - 60 mins
DEFROSTED REFRIGERATOR COILS, BUT DIDN'T REPLACE THE GROMMET.
Was this helpful?
Thank you for voting!
Freezer not defrosting and making fridge run warm.
2 of 2 peoplefound this instruction helpful.
Brent from PRESCOTT, AZ
Really Easy
30 - 60 mins
Nutdriver
Super simple following the instruction video you posted. Thanks!
Was this helpful?
Thank you for voting!
Freezer cold ; fridge warm . Freezer not defrosting.
2 of 2 peoplefound this instruction helpful.
Tim from Oxford, MA
Really Easy
1- 2 hours
Screw drivers
Unplugged fridge Pulled light cover off Used screwdrivers to press in on tabs holding control board cover. Unplug wiring harnesses. Snapped board in two. Install in cover Reattach wires Done
Was this helpful?
Thank you for voting!
peg that swings the pantry door open and closed was broken off
2 of 2 peoplefound this instruction helpful.
Dalton from BEAUFORT, NC
Really Easy
1- 2 hours
Nutdriver, Screw drivers
watched partsselect video and simply followed the directions
Was this helpful?
Thank you for voting!
When the support frame broke we threw the entire system into the trash DUH !
2 of 2 peoplefound this instruction helpful.
Bruce from CLARKSVILLE, VA
Really Easy
Less than 15 mins
Thanks for the video showing how to replace the Humidity Slide the knowledge that the end with the flair needed to be slightly bent to SNAP into place was a big help.
Opened the bottom freezer door and pulled the gasket out of the groove. Pulled it out around the door and put the new one back around the door and the pressed into the groove. There was one place that a flat spot didn't take shape so I used a blow dryer to heat it up some and now it seals perfectly.
Was this helpful?
Thank you for voting!
Right Door Magnet weak, door would not stay firmly closed
2 of 2 peoplefound this instruction helpful.
Larry from CHIRENO, TX
Really Easy
Less than 15 mins
Replaced seal on door. Same problem. Went to Lowe's and got several magnetic cabinet door catches. Attached them to the top of the door. (they can be seen sticking up), with the magnet part screwed to the door and the metal plate attached to a small wooden block glued to the top of the body with contact cement. Cost abound $16.
... Read more> "To infinity and beyond."
Read less
Was this helpful?
Thank you for voting!
Cracked humid drawer
2 of 2 peoplefound this instruction helpful.
Julie from BATH, PA
Very Easy
Less than 15 mins
Complete replacement of the plastic drawer.
Was this helpful?
Thank you for voting!
Repaced the right-side door light switch
2 of 2 peoplefound this instruction helpful.
Charles from SEGUIN, TX
Very Easy
Less than 15 mins
Pliers, Screw drivers
Killed the power to the fridge. Then, used a small, thin screwdriver to depress the clip on the bottom of the switch and wriggled the old switch out. The two wires easily came off the contacts with pliers. Connected the wires to the new switch and snapped it into the hole--clip facing down and contacts facing up. Turned the power back
... Read more on and checked the switch. Worked perfectly! Easy job.
Read less
Was this helpful?
Thank you for voting!
The center rail was broken
2 of 2 peoplefound this instruction helpful.
Joella from THE DALLES, OR
Very Easy
Less than 15 mins
The part just snapped in. super easy.
Was this helpful?
Thank you for voting!
The vertical mullion rail went bad
2 of 2 peoplefound this instruction helpful.
Ed from OCEAN CITY, NJ
Very Easy
Less than 15 mins
Nutdriver
I left this broken rail hang off my refrigerator for almost a year I finally decided to investigate the possibility of ordering the part on line. I found the part on line in minutes and when I received the part it literally took me 3 minutes to install.
My Orders
