AEC6540KFB01 Maytag Dryer - Instructions

Took 2 screws under front edge of smooth top. Unscrewed ground wire from back of smooth top unit. Unplugged 2 wire bundles, from back. Took bad element out , put in new one. Put back together. About 10 min's tops. Easy peasy.

Removed and replaced above named parts, rewired.Be sure to tighten all nuts that secure wires. I believe this is what caused the problem.

really easy! Removed 2 screws under the glass top at the front, access from the open oven door, then removed the ground wire, removed the stove top, took the element holder off,( 2 screws)and replaced with new element, 30 minutes. I ordered the part and came within 18 hrs of ordering it, fantastic experience.

Turned off power.Removed 2 screws, flipped top over, removed old element, replaced new element,turned over top,fasten down with 2 screws.Turned on power. Turned on burner,made coffee-took a brake.

Lift the cooktop out of it's inset in the counter top, flip it upside down and lay it on towels to protect the cooking surface. There is a raised rectangular panel that covers the switches located about the center front of the bottom. Remove this panel with a small nut driver to expose the switches. Now, locate the dead switch and place a ... Read more strip of masking tape pointing to it and lapping around the edge so it can be seen when the unit is flipped back upright. Flip cook top back upright. Locate the correct switch by observing the masking tape. There are two small, short-threaded, phillips screws holding the switch in place. They must be accessed from the knob hole (remove rubber grommet)and at a slight angle. There is very little room to extract the screws...this is where I used the magnet to magnitize the tip of a small screw driver. Once the screw is free of the threaded hole, lift it with the magnetized screwdriver out through the knob hole. The switch will fall out easily when the two screws are removed. If you drop one of the screws inside the stove top, don't panic, I was able to shake the cook top and retrieve the screw. Now, flip the top back upside down. Using a pair of pliers remove each wire one at a time from the bad switch and connect it to the same terminal on the new switch...this way there can be no mistakes. Be sure the rubber insulator removed from the bad switch and placed on the new one. Position it where the screw holes show through, then place the switch in position. Turn the top back over in the upright position but position it where you can reach underneath it with your left hand. You will have to hold the switch and maybe move it around slightly to aline the screw holes when replacing the screws. Take a screw on the end of the magnetized screwdriver and carefully insert it into the knob hole and into the switch bracket. once you get one started, the other will be easy. I don't recall the screw replacement being any problem, just that you have to handle the screws carefully, so as to not drop one inside the cook top. Now, flip the top back over and replace the cover over the switches and replace the top in it's cabinet. The job is complete, Oh, and don't forget to flip the stove's cirduit breaker BEFORE even touching the stove!

Remove top by opening oven and taking out two screws in the front. Lift up top and unplug wire connectors on bad element, writing down where they are landed. Take out screw on element bracket and replace. That easy. Be sure to unplug appliance for your safety. :-) Also just wanted to add that PartSelect was great. Ordered it on saturda ... Read more y and was cooking with it on tuesday. Great job.

So, the F9 error indicates a electrical power issue. First I pulled the oven out and verified I had 240 volts at my outlet.

Then I removed the fire panel over the terminal block and the issue was apparent. The nuts on the terminal block were corroded. This had cause the resistance in the connection to raise and burn up the ... Read more wire to my oven plug at the terminal block.

I removed the whole back panel and everything else seemed OK visually.

1. I go new connectors for the oven plug, stripped the wires, and crimped on the new connectors.

2. The terminal block DOES NOT come with the nuts to connect the wire to the terminal block. Mine were so corroded they had to be replaced. So I went and purchased the correct ones and installed the terminal block and reconnected all the wires.

3. I applied some dielectric grease to the connections through out the process of reinstalling to prevent it from happening in the future.

First, turn the breaker off then unwire the power harness. Lift the unit out, it’s a little heavy. Lay it on a flat surface and remove approximately 10 screws with a 1/4 socket. Lift off ceramic top to expose elements and switches. There is a baffle on the right side by the switches, remove 3 screws and lift out, Your switches are now exp ... Read more osed, just remove 2 Phillips head screws and the switch will come out. Just switch the wiring connectors and reinstall switch. Reverse disassembly steps. Good luck!

Had a technician from Home Advisor to check the problem out with my Whirlpool Double oven(1 1/2 old). Paid $60 to find the problem. According to the technician problem was control board and cost of labor and parts $465.00
Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answer ... Read more ed my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine.
Thank you, Thank you Part Select for your help and honesty.

Sincerely
Peter from Maryland

After identifying the part and taking delivery of it, I opened the breaker for the unit and then removed the range top by taking out 2 Phillips screws and lifting the part away from the hinges in the back. The element was attached with only 2 spring loaded clips which I then removed, noting the numbered position of each. I then photogra ... Read more phed the wiring (x4) from several angles and removed each of them. I attached the clips to the new element and reconnected the wiring to the main heating element and the sensor per the photographs. The element was then re-positioned into its mounting slots, the range cover was reattached with the screws and the unit tested once power was restored.

Took off top and pulled out old element and plugged in the new one

Shut off breaker. Remove a total of 3 screws attach wires, replace screws, turn breaker on. Done!

I watched the video you provide and it answered all my questions. You estimate repair at 10 minutes. My wife said I waz done in under 10 minutes Watch the video, it explained every step and all the little tricks to the snap connections.

After many years of use by average families, the cooktop was firmly adhered to the countertop by kitchen contaminates (mostly dried grease) that entrained between the cooktop and the countertop.

Popping it loose with my geezerly muscles was hopeless, so I took 2 pieces of 3/4" plywood to spread psi (at the bottom of the cooktop ... Read more and at the top of the shelf below it), plus a 2 X 4 stud and more plywood as shims... placing in-between that plywood; a scissor jack from my pickup truck.

Locating this assembly to apply force at one end of the cooktop minimized the stress at the adhesion on the countertop. Results were no problem and no damage, in this case, in breaking the adhesion.

After that, a 1/4" nut driver did the loosening and tightening. A magnetic #2 Phillips screwdriver did the sheet-metal screw starting. A slot screwdriver was used to loosen the electrical connectors at both ends.

The repair was trivial; most of my time was spent in investigation, part acquisition, and setup. Here's hoping the above might cut your losses in that regard.

I shut off the breaker to the stove. I removed 2 screws from the underside of the cooktop at the front of the unit. I raised the cooktop and had my helper hold the top at an angle to access the burner. I removed 2 screws attached to the burner and then loosened the 2 clips and moved them to release the burner. I transferred the electrical ... Read more connections from the old to the new. Reinstalled the burner and cooktop. Turned the breaker on, tested the new burner and I was fone