My Orders
- Home
- ACS3350AW0
- Instructions
ACS3350AW0 Amana Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Autolatch assembly did not work
3 of 5 people
found this instruction helpful.
-
Jeff from Wrightstown, WI
- Really Easy
- 15 - 30 mins
-
Screw drivers
The repairman that had come had stated that this part is no longer made, but I was able to locate one through PartSelect and was able to replace it with minimal effort.
I removed the three screws that held down the stove glass top surface and had a person hold the stove top up while I removed the two screws which held the autol ... Read more atch assembly in place. I then swapped the leads from the failed assembly to the new one and replaced the screws which were removed. New assembly tested out fine and oven was able to self-clean again.
I removed the three screws that held down the stove glass top surface and had a person hold the stove top up while I removed the two screws which held the autol ... Read more atch assembly in place. I then swapped the leads from the failed assembly to the new one and replaced the screws which were removed. New assembly tested out fine and oven was able to self-clean again.
Read less
Was this helpful?
Thank you for voting!
oven would not light/get hot.
3 of 5 people
found this instruction helpful.
-
gregory from sayreville, NJ
- Easy
- 1- 2 hours
-
Pliers, Screw drivers
I slid out the oven burner disconected the old igniter and replaced it with the new one & slid back in place and connected the two wires and I was back in business. The job was relativly an easy one.
Was this helpful?
Thank you for voting!
Cosmetic replacement of stove top burner bowls.
3 of 6 people
found this instruction helpful.
-
Larry from Owensboro, KY
- Really Easy
- Less than 15 mins
Easily replaced the stovetop burner bowls by removing the old ones and replacing with the new ones.
Parts Select provided easy online ordering and was nearly one-half the price of other online suppliers.The quality was excellent!
Parts Select provided easy online ordering and was nearly one-half the price of other online suppliers.The quality was excellent!
Was this helpful?
Thank you for voting!
Missing oven rack
2 of 3 people
found this instruction helpful.
-
Denise from Pittsburgh, PA
- Really Easy
- Less than 15 mins
Although this was not a repair I wanted to let you know your service was outstanding and the price quite reasonable. I am very happy to finally have a much needed second rack in my oven that was not there when I purchased my home. Thank You
Was this helpful?
Thank you for voting!
Broiler inoperative
2 of 3 people
found this instruction helpful.
-
Donald from East Syracuse, NY
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
For the third time in less than a year I had to replace the broiler igniter. The range is 27 years old and has given us excellent service. When the igniter failed it's replacement lasted 3 months. The next replacement lasted about 6 months. This last replacement has been in service about 1 week. We shall see. The last one had an open wire
... Read more
within the ceramic mould. There was continuity from one wire, through the black portion, but not to the second wire. It seems like it was a fault in manufacturing.
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't heat
1 person
found this instruction helpful.
-
Timothy from Madison, AL
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable)
WEB research indicated that even though ignitor would glow, that it was likely faulty.
Turned off power at circuit breaker
Remove shelves and bottom plate from inside oven.
Unscrew deflector plate
Remove drawer under stove
Remove ignitor and unplug from connector
replace ignitor, plug in, reassemble stove. ... Read more r />Needed flashlight to see under stove.
Turned off power at circuit breaker
Remove shelves and bottom plate from inside oven.
Unscrew deflector plate
Remove drawer under stove
Remove ignitor and unplug from connector
replace ignitor, plug in, reassemble stove. ... Read more r />Needed flashlight to see under stove.
Read less
Was this helpful?
Thank you for voting!
Gas oven would not light
1 person
found this instruction helpful.
-
Elizabeth from Vernon, CT
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
I have an older model gas oven which required that all screws had to be removed. With a screw gun the job would not haven taken long. Once the bottom pan was removed the oven ignitor took some finese to remove. This was only due to the short wires. Once pulled sufficiently to be able to disconnect the ignitior (although I was afraid I
... Read more
was going to pull the wires and separate them from the stove), it was very simple to unplug and plug in the new one (again, making sure to hold the plug so the wires would not retract back behind the wall which would have required the stove to be pulled out from the wall and the back disassembled).
The good news, it was a success and the oven works like new. Roughly $38.00 later, I am back cooking. The extra effort for the screws was offset by being able to complete this by myself and saving the cost of a repair man. Would do it again.
The good news, it was a success and the oven works like new. Roughly $38.00 later, I am back cooking. The extra effort for the screws was offset by being able to complete this by myself and saving the cost of a repair man. Would do it again.
Read less
Was this helpful?
Thank you for voting!
Gas oven would not heat up
1 person
found this instruction helpful.
-
John from Blairsville, GA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
My repairman told me it was probably the ignitor (even though the old one sitll glowed), but after weeks of waiting for his back-ordered part, I decided to try it myself - found it on PartSelect and had it 3 days later. Turned off the power to the oven. Slid out the 2 racks, and the cover below the racks. Unscrewed 1 nut and removed th
... Read more
e V shaped metal plate that distributes the heat. Under that removed 3 screws that hold the ignitor clip in place and got the igniter out of the clip. I couldn't get to the plug on the other end of the ignitor until I took out the oven drawer and removed 2 screws holding a metal cover in place below the oven. Reversed the whole process being careful with the end of the new ignitor (I read it was fragile). The oven now heats up in 5 minutes and maintains temperature again!
Read less
Was this helpful?
Thank you for voting!
The oven would take 45 minutes to over an hour to preheat.
1 person
found this instruction helpful.
-
Timothy from Elk Grove Village, IL
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
I removed the oven door by removing two screws, one above each hinge. With the door screws removed, position the door to the slightly open position and lift strength up to remove. Remove wire racks and the cover from the bottom of the oven. Remove the heat deflector which is held on with a single nut. Remove the screws that hold the cavit
... Read more
y that houses the igniter and the burner. The igniter is held in place by a protective bracket that has to be reused. I slid the old igniter out of the protective bracket and then removed the cavity by allowing the burner and igniter to exit through an opening in the rear of the cavity. The drawer (broiler pan storage) had to be removed to remove the two screws to an access panel that allowed access to the igniter connector. After disconnecting the old igniter, I fished the new igniter connector through the back of the oven to connect it. I use masking tape to hold the access panel in place while reinserting and tightening the two screws. Replace the cavity that houses the igniter and burner. Slide the protective cover over the igniter. Realign and secure the burn and igniter assembly by reinserting and tightening the necessary screws. Reinserting and tighten the screws around the igniter/burner cavity. Replace the heat deflector by tightening the nut. Replace the cover that covers the bottom of the oven and the wire racks. Reinsert the drawer. Slide the door over the hinges and reinsert and tighten the two screws.
Read less
Was this helpful?
Thank you for voting!
Range top worked; broiler worked; oven would not heat.
1 person
found this instruction helpful.
-
Philip from W. Bridgewater, MA
- Easy
- 15 - 30 mins
Disconect power source; Remove oven racks, remove storage drawer under oven; remove floor of oven, remove flame deflector, remove three screws holding igniter cage and unplug faulty igniter. Reverse all steps for reassembly.
Was this helpful?
Thank you for voting!
Oven would not light
1 person
found this instruction helpful.
-
Verno from PRINCETON, WI
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I had done this before, but a while back, so it took a little longer to disassemble and find the igniter. Once there, easy to troubleshoot with a meter. Reassembly was only a few minutes and part of that was finding a new nut, since I lost one. I had to remove the storage drawer, then remove a metal cover to get at the connections. I te
... Read more
sted the power to the igniter and found it to be OK. I tested continuity and had some but very low. Pulled the diffuser and cover off burner to locate igniter. Ordered part,put it on and reassembled everything. Working fine.
Read less
Was this helpful?
Thank you for voting!
oven died
1 person
found this instruction helpful.
-
Ben from Lawrenceville, GA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers, Socket set, Wrench set
looked at and saw that ignitor was cracked,saw simple repair ahead. just needed the right part . Without part , select simple ,and easy selection, i might not have ever found the right part. as i said before finding the right part is 90 percent of the job and they made that an easy task .
of course if you want me to describe ... Read more in detail, took out the pan saw the bad ignitor, removed 2 serews, disconnected 2 wire, the reassembled in the opposite direction. 30 minutes tops. I am sure this saved me at least 150 bucks for some "so called reparman" to do the same job, Most people do not realise that they have more education than most of these "repairmen". The only advantage these "repair people" have is acess to schematics and part numbers. Part select is a good start on putting this information in the hands of us average "idiots" as I am sure the repair folks call us when we pay 200 bucks for a 30 dollar job.
of course if you want me to describe ... Read more in detail, took out the pan saw the bad ignitor, removed 2 serews, disconnected 2 wire, the reassembled in the opposite direction. 30 minutes tops. I am sure this saved me at least 150 bucks for some "so called reparman" to do the same job, Most people do not realise that they have more education than most of these "repairmen". The only advantage these "repair people" have is acess to schematics and part numbers. Part select is a good start on putting this information in the hands of us average "idiots" as I am sure the repair folks call us when we pay 200 bucks for a 30 dollar job.
Read less
Was this helpful?
Thank you for voting!
Gas valve would not open to let the gas flow to burner.
1 person
found this instruction helpful.
-
Matt from Billerica, MA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Simple install - 6 -7 screws one nut. Once replaced oven worked good as new. Part shipped from PartSelect actually better than one installed by repairman 4 years ago - fit like an original part.
Thanks PartSelect.com
Thanks PartSelect.com
Was this helpful?
Thank you for voting!
oven very slow to light
1 person
found this instruction helpful.
-
Larry from Circleville, OH
- Really Easy
- 15 - 30 mins
-
Screw drivers
First I had to take the drawer completely out of the stove to reach the igniter. I then removed the screws that held the igniter in place and removed it. I had to slightly modify the replacement part by squeezing it together to make it fit into the same space. I put the replacement igniter in place and screwed it down; put the drawer b
... Read more
ack in the stove and turned on the over to see if it would light. Bingo, job done!
Read less
Was this helpful?
Thank you for voting!
The Oven would not turn on reliably
1 person
found this instruction helpful.
-
Carlos from Grand Rapids, MI
- Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Remove the racks
remove one nut that holds the heat deflector
3 screws that hold the igniter
remove the drawer
remove 2 screws holding a heat shield in place.
unplug old igniter and reinstall
remove one nut that holds the heat deflector
3 screws that hold the igniter
remove the drawer
remove 2 screws holding a heat shield in place.
unplug old igniter and reinstall
Was this helpful?
Thank you for voting!