ACG150NLD1 Frigidaire Refrigerator - Instructions

After unsuccessfully trying to change the blown light bulb I discovered that the plastic light socket had gotten so hot that it melted and permanently fused with the blown bulb. After my new socket arrived in the mail I just popped the temp control assembly out with a screw driver and removed the old socket and placed the new one in. ... Read more Whole operation to 5 minutes.

There are quite a few bolts that needed to be loosened to remove the old gasket and put on the new one. We tried to do it by just loosening and leaving the door on the fridge...take my advice. Just remove the door, remove all the bolts, put the new gasket on and replace the bolts then the door. MUCH EASIER than trying to fit it on inch ... Read more by inch and having it pull back out etc.

I unplugged electrical cord to the freezer. I removed the cover to the relay and load protector. I labeled the wires and made a diagram on the proper placement of each wire going to the relay. I unplugged each wire and removed the relay. Then I removed the load protector. I installed the new load protector and new relay. I placed the wire ... Read more s on the proper terminals of the relay. I replaced the electrical cover to the relay and load protector. I plugged the electrical cord back in the electrical outlet. My freezer started working again. I placed several bottles of water in the freezer to make sure the freezer was working properly before I restocked it with food.

Thanks again for the help. You just saved me about $400.

The BIG problem was getting the old drip pan off. The bolt on top of the compressor was too long to allow the removal of the old drip pan. I removed the old drip pan by cutting most of it away with tin shears then cutting the remaining part of the pan around the bolt with a hack saw (taking care not to damage freon lines and raising the p ... Read more an above the threads of the bolt so as not to damage the threads). I still had to cut half the bolt away with a hack saw by replacing the nut and cutting a third of the bolt away (above the nut), so the new pan would fit. Putting the new pan on was a breeze after that. It may be easier to just cut the bolt off altogether on top of the compressor and use the wire clips per the instructions supplied with the kit to install the new one.

Simple switch repair: Unplug fridge, pull down to remove switch assembly, slip contacts off. Reverse with replacement switch. HOWEVER, check first to see if the bulb filament might be broken, as this could cause the same symptom. OR in my case, the light socket connection was the culprit. Check that too before ordering a replacement s ... Read more witch.

Twisted replacement bulb into place easily. Let there be light!

I opened the fridge door and lifted up the old gasket to investigate the situation. I saw that the inside door panel (the one that has the butter compartment and additional shelves for condiments) had screws every few inches. I determined that this was holding the smaller lip of the gasket in. I got out my trusty cordless drill and wen ... Read more t to work. After a few mild cuss words, I did manage to get the very last corner on, as that is the trickiest part of the installation. Note that I am an almost "60" year old woman who has many other tools, including a chain saw, which I utilize every now and then. So if I can do it myself, I certainly will! The best thing of it all was that I ordered the part on 8/22/08 and when I arrived home the evening of 8/24/08, the box with the part was sitting on the back deck. Thank you partselect for a great product and great service.

I should have read everyone else's experiences before attempting. I did view a youtube video and thought I had it set. However, if I had it to do over, the door would have been removed. The door shelf (inner door) taken off and cleaned before attempting to put the gasket on. I did it while the door was still attached and probably lost a g ... Read more ood 45mns along with my fingers cramping, knee's flat spotting, and lower back catching fire. TAKE THE DOOR OFF if at all possible, you wont regret it.

Removed numerous screws, be careful removing old gasket to not crack door.

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

Removed plastic male parts. Inserted new end caps onto old retainer bar. Inserted all into door. A snap, but I didn't need to order the retainer bar after all - the old one was the perfect fit and the one I ordered was way too long. I returned the new retainer bar, and the shipping was more expensive than the part.

There was no work to do. I just slipped the new drawer in. I'm writing because PartSelect was amazing. A rep on the phone helped me identify the part I needed--which was a substitute b/c the actual part isn't made anymore. The next day, the part arrived. I was blown away and want to acknowledge the great service.

I just had to make certain I had the correct end-cap for the correct side. I placed the two little curved pieces into the slots and applied some downward pressure (gently) onto the end-cap till I heard it "snap" into place. You could then see that it was held in place securely. I did first one side, then fed the bar into it, then placed t ... Read more he other side onto the the bar; inserted the end-cap and secured it in place.

HINT: I myself mistakingly ordered the same exact end-cap for both the freezer and the fridge doors. I was unaware (I failed to check), that the end-caps for the freezer are not the same end-caps as the ones for the fridge door. My refrigerator uses three different end-cap sizes; one size for the actual fridge door and two additional different sizes for the freezer door. Not wanting to exchange it, I used the one I ordered anyway. It still works, but makes the bar protrude into the freezer more than it would have, had I ordered the correct size.

SPECIAL NOTE: This company got the correctly ordered products to me within a couple of days. I would definitely order from them again without hesitation. I am very happy with the product and service. Smooth.

We ordered end pieces for the shelf holder, attached them to the long piece and snaped them into the door. Three minutes to open the box, attach, and close the door. A less than 20 dollar repair and success!