ACB6 - Instructions

Extremely simple repair to make. Move stove away from wall and disconnect power. Remove the oven racks. Remove the rear sheet metal panel covering the wiring harnesses. Caution: Sharp edges and corners on sheet metal.Sensor is located in upper left corner on rear oven wall. Using a long-shafted #2 Philips screwdriver, remove the two Phili ... Read more ps head screws and gently pull the sensor 1" away from the oven wall. At this point, it will help to have an assist from someone while you are behind the range. Have the assistant gently tug on the sensor while you watch for wires moving on the rear of the range. After locating the sensor wires, gently disconnect the plastic connector clip. Note: plastic connectors become brittle with age and exposure to heat Move to front of range and gently remove sensor from rear wall by pulling the wiring through the oven wall. Before inserting the new sensor wire through the oven wall, "dry fit" the wiring connectors to see that the new sensor is a correct connection. Make connection, and secure the sensor to the rear oven wall with the two screws. Install racks, reinstall rear sheet metal panel, and connect the power. Set the oven baking temperature to a moderately low temp, 300 - 350 deg. to test the new sensor.

I removed the two mounting screws and pulled the harness through the opening unsnapped the sensor from the harness and installed the new sensor i didn't have to used the adapters the new sensor fitted

(1) Turn off power;
(2) remove 4 phillips screws on the bottom of the control panel (top of the oven door) to allow the control panel to rotate up and out;
(3) remove 2 electrical connectors by releasing locks then pull/wiggle free. (note the cable locks to help orient reassembly) You can now carry the control panel to the kitch ... Read more en table to continue.
(4) This was a little tricky for my big hands: remove the switch / controls ribbon cable by depressing small tabs inward then releasing a small wedge which squeezes the ribbon into the connector. Gently unhook and separate the ribbon cable from the display module.
(5) remove 4 hex-head screws which mount the clock panel to the control panel assembly.
(6) reverse procedure to reassemble & test.

I opened the top oven. Then unscrewed the screws below the display unit. Took off the attaching wires. Unscrewed the broken display. Screwed the new display back on. Re-attached the wires. Screwed the support screws back on. It took about 10 minutes.

The only "difficulty" was in removing the wires. One of them is attach ... Read more ed in a pressure attachment which isn't immediately obvious (that's the largest attachment in the center). Just be careful when taking that one out.

installed part,turned unit on-temp still cold. reset digital control, up 35 degrees, still cold. un-plugged unit,re-connect after 10 min. still cold.

Took out 7 screws. Removed front panel, unhooking ribbon cables. Used nut driver to remove old display from the panel and then install new display. Replaced the 7 screws.

Remove phillips screws from below upper face cover. Unclip wire connections. Use nut driver to remove Electronic display. Reverse operation. Careful on reattachment of flat wires to plastic clip. The explanation from other customers made this very easy.

removed the trim bezel housing the controls and clock assy, by removing 3ea phillips head screws on top and 4ea screws on the bottom of the trim bezel. disconnected the wiring harnesses. removed the 4 screws securing the LCD assy to the bezel. Repeated the process in reverse for installing replacement unit. Very simple. One n ... Read more ote: Always shut off power to the appliance from the breaker panel. it will ensure proper reset of the panel when the power is turned back on. this is a procedure a 10 year old could handle. very simple and no electrical experience necessary. Saved myself at least $300 for a few minutes of my time....

Replaced the thermostat according to existing videos and had to adjust the thermostat using instuctions in the user manual for model CWE4800ACB.

My wife help take the door off. It was a little heavy . The door came apart very easy and went back the same way.We save over $300 by doing it our selfs.

I installed the new oven sensor but the problem continued. So I ordered a new relay board and installed it. Still no luck. So I pulled the new board back out and started trouble shooting it using my electronic background. I discovered the new board was using a pin for L2 that had no exit on the backplane, so I removed it and installed ... Read more it where I believed it should go. Reinstalled the power relay board and presto. My oven is working lie a champ. Louis

Had to remove oven from mounting cabinet to get to the back since the wire lenght to the conector was to short to come through the mounting hole.
Other than that the repair was straight forward. 4 screws to dismount the Oven from cabinet, 2 screws to remove Sensor and 3 srews to open the back of the oven once out in the open. New cab ... Read more le adapter that came with the new sensor was needed in my case.

Shut of power to unit, removed front display panel, located lower circuit board. Removed the one screw holding existing board and installed new board, then swaped wires from damaged to new. re-installed front panel, turned pwoer back on, that was it. The unit is working well.

First, I turned the power off to the oven. With a screwdriver, I removed the 3 screws above and the 4 screws below the control panel. Next, gently pulled out the control panel. Three cables attached the electronic clock assembly to the bundle of cables controlling the oven. By pulling on the plastic tabs, I was able to loosen two of th ... Read more e cables. The other "cable" resembles a ribbon. Squeeze the black tabs on each side of the base of the ribbon connector and pull slightly. The ribbon itself then needs to be bent and gently removed from the connector (you can see two slits in the ribbon that hold it in place). Using my wrench set, I removed the four screws that held the electronic clock assembly to the control panel. Then I attached the new clock assembly, replaced the cables and ribbon cable, snapped in the control panel and secured it into place with the seven screws. It was very easy to do this.

We were selling our house and the inspection report noted that the Clock on the double oven didn't work and needed to be repaired. I called the service company to get an estimate. They said $536.00 for replacing the Clock Assembly. I went to your site, saw the schematic, found the part for under $150.00 and ordered it. It took me 10 minut ... Read more es to install it. Because of you I saved nearly $400.00! Thanks for the quick and reliable service I will reccomend Parts Select.com to everyone!