Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Freont Burners Of Both Units Had Rusted Though Over The Years Of Boilover.
3 of 4 peoplefound this instruction helpful.
Angelo W. from Chirfland, FL
Really Easy
Less than 15 mins
Lifted lid, removed old burner units, replace with new ones. In less than two min. Was back up and cooking.
Was this helpful?
Thank you for voting!
floor panel heavily stained and warped
3 of 5 peoplefound this instruction helpful.
Joel from Monroe, NY
Really Easy
Less than 15 mins
slide latches in rear of floor panel forward and remove.
Was this helpful?
Thank you for voting!
1960's oven door gasket fell apart, actual gasket not available any more
2 of 2 peoplefound this instruction helpful.
Mary from WINCHESTER, MA
Really Easy
15 - 30 mins
Screw drivers
Chose rubber flexible gasket with metal tabs. cut to size. unscrewed metal bracket on inside oven edge on 3 sides, slipped metal tabs between oven and metal and screwed back in. Done! Not a perfect fit but pretty good - better than no gasket.
Was this helpful?
Thank you for voting!
gas range knob and oven knob for my magic chief stove broke
2 of 2 peoplefound this instruction helpful.
Sandra from MONTCLAIR, NJ
Really Easy
30 - 60 mins
After going to Homedepot, Sears, Lowes and other hardware stores I reached out to some folks at my job i was recommended to order the parts from PartSelect. I spent the Christmas and New Years Holiday in a mess. I really could not cook like i wanted to. I ordered the parts within a week it came. I am thankful you to guys no more drama,
... Read more caos or worries. I highly recommend this site very easy to install. thank you
Pilot light would go out when oven was turned off but still allowed gas.
5 of 11 peoplefound this instruction helpful.
Steven from Oklahoma City, OK
Really Easy
30 - 60 mins
Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
l removed the top section after the grates. Then l took the phillips screws out of the three brackets which hold the L brace which supports the controls,thermostat and the regulator. Only because l did not have a closed-end ratchet wrench for 1/4" and l could not locate my 1/4" socket for my small rachet. l disconnected all gas lines and
... Read more the thermocouple, then l used the power screwdriver without the apex which makes it a great power 1/4" nutdriver and took out the two screws holding the thermostat. Then l just reversed all the steps installing the new thermostat and once l got the air out and gas was pure l lit the pilot lights and everything worked great. And l adjusted my top burner pilot lights a little higher to prevent them from gettig blown out so easy. Done deal.
Read less
Was this helpful?
Thank you for voting!
Broken burner knobs on stove.
2 of 3 peoplefound this instruction helpful.
Barbara L. from Tewksbury, MA
Really Easy
Less than 15 mins
Just replaced the old burner knobs with the new !!!
Was this helpful?
Thank you for voting!
I needed a broiler pan
4 of 9 peoplefound this instruction helpful.
Rhoda P. from Secaucus, NJ
Really Easy
Less than 15 mins
I took the broiler pan out of the shipping container and put it in the oven.
This was not a difficult task. I just slid the valve knob on the shaft, repair was complete. This was a very easy diy project.
Was this helpful?
Thank you for voting!
needed a new knob
2 of 4 peoplefound this instruction helpful.
Clayton from Shortsville, NY
Really Easy
Less than 15 mins
pulled the old one off and push the new one on
Was this helpful?
Thank you for voting!
The oven control know wore out.
1 personfound this instruction helpful.
Judy from ARDSLEY, NY
Really Easy
Less than 15 mins
I purchased a knob that I was hoping might fit properly. Unfortunately I did not find anything that matched the knob we had originally. We use the knob that I purchased to turn the oven on and off, but the shaft channel is much longer than the shaft on the stove, so the knob sits high above the other knobs. I wish that I could find
... Read more a knob to accommodate the shaft on the stove. I have considered purchasing an addition kinob and trying to saw off part of the shaft if the plastic can be shortened without shattering.
Read less
Was this helpful?
Thank you for voting!
unable to see the numbers on the old knob.
1 personfound this instruction helpful.
Patricia from SAN LEANDRO, CA
Really Easy
Less than 15 mins
ordered it had to line it up then just popped it on.
Was this helpful?
Thank you for voting!
Oven knob was broke
1 personfound this instruction helpful.
Sara from FORT RIPLEY, MN
Really Easy
Less than 15 mins
Got the new one and put it on
Was this helpful?
Thank you for voting!
35 year old range. grates too dirty to clean. Parts Select had exact replacement grates. Perfect fit.
1 personfound this instruction helpful.
FRANCES from AFFTON, MO
Very Easy
Less than 15 mins
Easy, removed from box, put in place on range. Happy customer. Good company to find exact replacement parts.
Was this helpful?
Thank you for voting!
my knobs were broken on 30 year old range
1 personfound this instruction helpful.
Larry from LAWTON, MI
Very Easy
Less than 15 mins
Pliers
I took a pair of channel locks pulled the old one off pushed the new one on they look really nice and was glad they had the parts for such an old stove. thank you,now my hubby is glad so he doesn't have to buy a new stove.
Was this helpful?
Thank you for voting!
Old seal breaking off oven door. Oven not baking food well, wasting heat and fuel.
1 personfound this instruction helpful.
Mz from COLUMBIA, ME
Very Easy
Less than 15 mins
Pliers
Used pliers to remove clips and old seal. Snap in new seal. DONE! Less than 5 mins.
My Orders
