911959 Kenmore Range - Instructions

New one a little different ,but it was marked for wiring!
Had to install upside down because wires would not reach right side up!
Had to pull back side of knob out and turn 180 degrees and glue in knob, so knob would be right side up!
Works fine! Now all burners work again!

First shut the power to the stove,then had to slide the stove out so I could get at the back to remove the panel screws.Once you have the back off remove the knob on the front.Under the knob is 2 phillips screws that you need to remove.Next I took the new switch and matched up the wires to the old switch.Reinstall is the reverse.Once the ... Read more switch is in place you must remove the excess shaft to match the length of the old one.This is done with the use of 2 pliers,you grasp the shaft with both pliers and snap it off where you need it.The kit comes with spacers so you have got to match up the right one so the switch is solid on the shaft.This finishes the project,next turn the power back on and check that all is working ok.Job finished.

Unscrewed the heating element from the inside back of the oven and removed the housing cover from the back of the stove to access the terminals. (The unit had arked and fused the terminal to the connector.) Installed the new unit and replaced the housing cover on the back and screwed the unit into the back of the oven. Works like a charm ... Read more .

GE changed the design a little, moving a connector so the existing wires didn't reach. I texted the model number to an address provided with the part, and GE returned a URL for installation instructions. The instructions said there should be two jumpers to extend the wires, but there was only one, so I had to make a trip to the hardware ... Read more store to get connectors to make my own jumper. Read the instructions carefully for where to connect the wires. My initial connection was wrong, but nothing bad happened, just the unit didn't heat. Two mounting tabs from the old unit need to be moved to the new. Heat shrink tubing is provided to cover the joints where the jumpers connect to the old wiring. If the jumper hadn't been missing, it would have been a quick, easy install.

When I ordered, nobody (19 different web sites) had the part in stock. GE took over 2 months to ship the part to PartSelect, but finally the stove is fully functional again.

My cooktop is a stand alone unit mounted in a counter top not associated with an oven.
-Removed power to the cook top. Breaker off.
-Lifted the cook top straight up from the counter top and placed two 24 inch board strips to support it above the counter top. This was very easy by pushing up from the bottom of the cook top. T ... Read more his is a two person job preferably.
-Removed the six phillip screws below the glass surface edge. 3 in the front, three in the back.
-Remove knobs and remove the glass top by lifting straight up.
-Record the wire positions on the element on paper and remove the connections.
-The element is mounted on two spring loaded studs that have spring clips as a retainer. Remove the two clips by pulling straight up with a plier or needlenose.
-The replacement element did not come equipped with the two mounting ears that the original had. I removed the two ears from the defective element and installed them on the new element. Very easy. Two phillips screws. The elements have perferations in the correct areas to accommodate this.
-Placed the new element in position and reinstalled the spring clips.
-Install the wiring terminals in the correct positions.
-Reinstalled the glass surface and the six phillips screws. Reinstall the knobs.
-Lower the cook top back into its counter top position.
-Return power to the cook top.
-Installation complete. Very simple!

Took off cover plate and removed screws from housing to switch. Connected each wire from old switch to new one. No problems.

I went online and ordered the part after reading other people's repair experiences, confident that I could do it because the part was quite pricey. First, be sure you're circuit breaker to your range is off. Next, open the oven door and locate and remove two screws with a socket, that are just under the top surface which will allow you to ... Read more lift up the glass top which is actually hinged...no need to pull the range out. Securely prop up the glass surface area and the burners are exposed. With a marker, mark where each color wire goes on the burner you are going to remove and also mark where the two holding brackets are. This way you can reference the locations to connect to the new one. Carefully remove the wires and brackets and install new burner with brackets and connections. Close up the top, replace two screws, turn on breaker, and if there were no other faulty components,it'll work great. P.S Be gentle getting the very snug wires off. Good Luck

Robert did not do the repairs. I did! 70 year old housewife. I watched a Utube video and thought I could certainly handle that. Ordered my part from your site. It came in two days. Burnet was replaced in under 20 minutes by me! Anyone can do this. Super easy, parts just plug in.

Pull the range out from the wall to access the rear of the unit. Turn off power to the range by unplugging from the wall or turning off the breaker.
Remove the large back cover from the oven portion of the range. Locate the two small wires and connector which is located between the two connections for the broiler heating element. Unp ... Read more lug the small connector.
Open the oven door and remove the screw that holds the temperature sensor in place between the broiler heating elements on the inside of the oven. Gently pull the sensor and the wire connector through the hole and discard.
Feed the new connector and wire through the hole from the inside of the oven. Attach the sensor to the oven wall with the screw.
Go to the back of the unit and make sure that no insulation has gotten into the oven space. Re-route the new wire being careful not to let it touch the contacts for the broiler heating element. Reconnect the wires to the connector and replace the back cover of the oven.
Plug in the range or turn on the circuit breaker. Slide the range back into place and re-level the unit. Test the oven to make sure the temperature is accurate and will maintain temperature.

Removed old hinges and installed new hinges.
Hardest part was determining that worn hinges were the cause of problem, then ordering replacements. GE website hinge on exploded view did not look like hinges I removed.Thanks to Google I got on to PartSelect.com website where excellent pictures of hinges and one-inch grid confirmed they ... Read more sold exactly what I wanted for my 13-year old range, the model number of which was not even on the GE website.

Open and slide door upward off of hinges. Removed bottom drawer to access hinge spring. Detached spring, noting proper hole in hinge for reinstallation. Removed three screws holding hinge and removed hinge. Compared new part to old...exact match. Inserted hinge, and reinstalled the three screws. Reattached spring in hinge hole. Sli ... Read more d door back down onto hinges. Done in four minutes flat!

I took the oven door off. Laid it down on a blanket on the floor. I pulled up on end going into the door, then went around with fingers to feel where the clip were and grab the clip with my fingers and gently pulled up. Then grabbed the new gasket, found the center clip that goes at top of door and started pushing the clips in. The last w ... Read more as feeding the ends back into the slot in the door.

Alls well that ends well. General Electric changed the configuration of our Light bulb socket on our 1996 oven. It did not have a flange with two screws as the original. The new one, you will just connect it and twist it into place. It worked and we are very happy. Such wonderful people to deal with at this site. Our sincere thanks, ... Read more
Richard and Shirley

Followed the video directions on your website - GREAT INFORMATION. Everything went very smoothly It took me longer to find my work light (after turning off the electric to the oven) out in the garage than it did to complete the repair!! SUPER PLEASED - WOULD NOT HESITATE TO RECOMMEND THIS COMPANY TO ANY DIY ADVENTURER!!

very easy remove the bad bulb install the new one