My Orders
911955 Kenmore Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Bottom element burnt out
6 of 7 people
found this instruction helpful.
-
Curtis from Oxon Hill, MD
- Easy
- Less than 15 mins
-
Screw drivers
remove two screws slide out. slide new one in. put two screws back. done.
Was this helpful?
Thank you for voting!
bake element
6 of 7 people
found this instruction helpful.
-
margaret from hastings, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
took 2 screws out of the element, then too the back off pluged in the element replaced two screws done
Was this helpful?
Thank you for voting!
Oven light did not work
9 of 16 people
found this instruction helpful.
-
Howard from Rio Vista, CA
- Really Easy
- Less than 15 mins
-
Nutdriver
Turned off power to the oven, Removed the oven light housing, installed new housing, turned power on and walla.
Was this helpful?
Thank you for voting!
my lower oven heater went out
6 of 7 people
found this instruction helpful.
-
lorita from bend, OR
- Really Easy
- Less than 15 mins
-
Nutdriver
i was really pleased getting the order from partselect. i had torn my oven appart and knew i needed just this one part i came home and ordered it from parts select and actually got the part the next day.... very nice.... so pleased
Was this helpful?
Thank you for voting!
switch went to high setting no matter what the setting was
10 of 19 people
found this instruction helpful.
-
Frank from Glen Cove, NY
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
took off cover, pulled all wires off switch, pushed wires on new switch, put cover back on. Whalaa..
Was this helpful?
Thank you for voting!
Bake element wouldn't heat
6 of 7 people
found this instruction helpful.
-
Leanne from Huntington, IN
- Really Easy
- 15 - 30 mins
-
Socket set
Removed the two screws that hold the element in place, then I disconnected the two wires and pulled the element out. I ordered the part and received it within two days. It was very easy to install. My oven was tunning in less than half an hour.
Was this helpful?
Thank you for voting!
Red Light On
5 of 5 people
found this instruction helpful.
-
Lawrence from DECATUR, AL
- Really Easy
- 30 - 60 mins
Red Light Off
Was this helpful?
Thank you for voting!
The small burner inside the double burner shortd out.
5 of 5 people
found this instruction helpful.
-
david from PORT ORANGE, FL
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
The first thing was to watch U-Tube . The replacement burner was being
replaced in a GE glass top range. Exter tools were required than depicted
in the U-Tube project. The project overall was not dificult for me however I was a general contracter for over 25 years
replaced in a GE glass top range. Exter tools were required than depicted
in the U-Tube project. The project overall was not dificult for me however I was a general contracter for over 25 years
Was this helpful?
Thank you for voting!
Glass- top range had two burners that would not regulate. Burners went to HIGH when dial was set on any setting, even low.
5 of 5 people
found this instruction helpful.
-
christopher from WOODSTOCK, GA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Replaced switches. Dual power switch had been updated and didn’t match original part but there were accurate instructions in package to allow correct wiring easily.
Good job Parts Select.
Good job Parts Select.
Other Parts Used:
Was this helpful?
Thank you for voting!
Light not working tried to Remove light assembly not knowing glass could screw out. Without thinking grounded exposed hot wire to burner bracket melting light socket connector. Had to replace socket.
5 of 5 people
found this instruction helpful.
-
Richard from CUMMING, GA
- Really Easy
- 15 - 30 mins
-
Socket set
First and most important trun off curcit breaker. Use 1/4 inch but driver to remove socket (2) screws. Remove ground and hot wire clips from old socket, replace on new socket. Screw back into oven ceiling and turn on power. Reset clock and your are done. Very simple.
Was this helpful?
Thank you for voting!
Outer ring of burner did not work
5 of 5 people
found this instruction helpful.
-
Barry from Bradenton, FL
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers, Socket set
1- opened oven door
2- unscrewed 2 screws underneath top with a socket wrench
3- unscrewed clips that held burner
4-used needle nose pliers to pull off wire clips off old burner
5- placed wires onto new burner
6- opened clips to make it easier to reinsert burner
7-reattached burner
8-Replaced top
... Read more r />The hardest part was unscrewing the 2 screws that held the top in place due to the position of the screws
2- unscrewed 2 screws underneath top with a socket wrench
3- unscrewed clips that held burner
4-used needle nose pliers to pull off wire clips off old burner
5- placed wires onto new burner
6- opened clips to make it easier to reinsert burner
7-reattached burner
8-Replaced top
... Read more r />The hardest part was unscrewing the 2 screws that held the top in place due to the position of the screws
Read less
Was this helpful?
Thank you for voting!
surface burner switch was burned
5 of 6 people
found this instruction helpful.
-
abbas from redmond, WA
- Really Easy
- More than 2 hours
-
Nutdriver, Screw drivers
After receiving the new swith from part select in less than four days with surface mail as they promised, it took me less than five minutes to replace the new swith with the old one. The only tools that I needed were A) a 5/16 nut driver to remove the back panel in order to get an access to the swith.B) a phillips screw driver to remove t
... Read more
he swith assembley from the front panel.
I had an estimate from a technician to do the job for 196.27 dollars!!!!!:(:(. I only paid 29.56 Dollars to part select to get this swith, including the shipping.:):):)
I had an estimate from a technician to do the job for 196.27 dollars!!!!!:(:(. I only paid 29.56 Dollars to part select to get this swith, including the shipping.:):):)
Read less
Was this helpful?
Thank you for voting!
When my wife tried to get the oven door apart to clean behind the glass front, she bent the Door Bottom Channel Trim, so I had to order a new trim piece.
5 of 6 people
found this instruction helpful.
-
Gary from STERLING, VA
- Really Easy
- 15 - 30 mins
-
Nutdriver
Consult the instruction guide that comes with the new part. Excluding doing some cleaning while things were apart, the operation took about 20minutes. 1. Open the oven door all the way. 2. Pull back the hinge latch on each hinge. 3. Close the door partially (about broil position). 4. Remove door by pulling so that hinges com out o
... Read more
f the slots. 5. Carefully set door face down on a table so that inside of door faces up. 6. With a Torx driver, remove 2 screws at upper part of inside of door. 7. With a nut driver, remove screws at bottom of Door Bottom Channel Trim. 8. Lift inside of door off, being careful not to lose the spacers that are behind the door panel at the upper part of the door. 9. With the nut driver, remove 4 screws that hold bottom trim to the side trim pieces. 10. Remove the old trim and replace with the new. 11. Align the left, right, and bottom trim pieces. 12. Reattach the 4 screws that hold the bottom trim to the side trim pieces. 13. Carefully replace the inside door panel, making sure the spacers are aligned properly between the main door pieces. 14. With the Torx driver, replace the 2 screws at the upper part of the inside of door. 15. With the nut driver, reattach the bottom screws at the bottom of the trim piece. 16. Carefully reinsert the door hinges into the slots (the door must be in the approximate broil position). 17. When hinges are properly inserted, door may be opened all the way. 18. Push the hinge latches back into hinges to secure door to oven.
Read less
Was this helpful?
Thank you for voting!
Broiler shorted out looked like a 4th of july sparkler.
5 of 6 people
found this instruction helpful.
-
Warren from Killeen, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver
Ordered on Tues got part on Thurs used a nut driver removed 2 screws holding element in top of oven,then removed the 3 screws holding the element and thermostat to rear of oven pull about 3 inches of slack, removed the blade plugs from element placed them on the new element and assembled it. Took abou 30Min. Easier if you remove the oven
... Read more
door!
Read less
Was this helpful?
Thank you for voting!
wire connection to socket was bad
6 of 10 people
found this instruction helpful.
-
David from Gansevoort, NY
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers
Disconnected the old socket ( 2 srews ) removed the two wires from the old socket, reconnected them to the new socket and reinstalled the lamp.
Was this helpful?
Thank you for voting!