91178 Kenmore - Instructions

Replacing the igniter was easy to do, that only took 15 min. The time was needed to take apart the bottom of the oven so I could get to the nuts on the igniter, and the time to put it back together again. I'm very inexperienced at this sort of thing so since I could do it I'd encourage anyone to give it a go, and anyone that knows what th ... Read more ey're doing will do it much faster.

Removed shelves and floor of oven. Removed burner unit to access screws attaching igniter to burner unit. Disconnected wires of igniter. Put new igniter in place and reinstalled burner unit. Reconnected wires using supplied wire nuts. Tested unit. Reinstalled oven floor and shelves once successfully tested. Cooked Pizza.

1.Took out the metal pan.
2.Removed the ignitor bracket.
3.Disconnected the two wire mount the new ignighter.
4.Connect the new ignighter wires to the wires still attached to the valve.
5.New igniter glow wonderfully.

removed the old part with socket set and replaced the part with a fresh one. turned on oven, igniter heated up and oven lit.

Replaced the oven igniter

Remove oven door,just open slighty and pull door up no tools.Take oven draw out.Remove oven floor held by two nuts in rear.You will now see the igniter,remove two screws holding it and the one screw holding the long tube at the front.The best tool I used was 1/4 drive socket set with a 6" ext.I did'nt need a new bracket that came with the ... Read more part and I cut the old igniter wires and wired in the new one because it had a special connectors.If your are a handy person,its EASY.

Replace igniter in oven. It was a simple repair and only required that I unplugged the power cord from the unit, remove the base and 2 screws holding the igniter.

Removed bottom of oven Removed bottom drawer. Removed two screws holding burner, disconnected both wires.Removed two screws holding igniter,installed new igniter reversing procedure.

Could not get at the screws holding the igniter to the buner, without removing the burner.

used nut driver to remove old module and 10 minutes the cooktop was back in operation

Easy Repair. Remove the storage draw under the oven. It lifts out. Lift oven door off of hinges. Remove 3 screws & unhook the spring. Reverse the procedure with the new hinge. Good as new.

After reading the other DIY's directions, we explored how to remove oven door. When the part came in, my sister who was visiting, removed the oven door (30seconds), removed bottom drawer (30 seconds), noted where spring was attached, took off screws and spring, installed new hinge with roller, took a minute to decide if the new hinge cam ... Read more e through the back or the front (front), she reattached the spring and screws. Put door back on and then struggles to put the drawer back into place. Total time less than 5 mintues, most time spent on returning bottom drawer to its home. Thanks part select for helping me not burn my self every time I try and get food out of the oven!!! I open the oven door all the way and am so delighted!!

The part arrived on timed and fit perfect. The repaired took 1/2 hour and everything works perfect. My wife thinks I am the best

Removed the oven door and the bottom plate. Remove existing igniter by cutting the wire and unscrewing two small bolts. The installation of the new part is the reverse.

I only wish I would have taken the drawer out first to get at the wire connections. Instead I tried to get at them by trying to remove all the layers of sheet metal at the bottom of the oven - to no avail. Once I took the drawer out and saw the connections and bolts to remove that held the igniter/gas diffuser there was no problem. The ne ... Read more w igniter does not come with the connectors on the ends so I simply cut off enough wire from the old one and used the wire nuts that came with to splice the wires. Simple reconnect and now we're "cookin' with gas" again.

It took a while to determine the cause of the problem because I was not familiar with gas appliances.After finding the problem I ordered a new igniter. The part was there in two and a half days!! I had it partly apart when the part arrived so it only took about 30 minutes to complete the repair. I would recomend PartsSelect to anyone. I h ... Read more ave never had parts come that quickly.