911725 Kenmore Range - Instructions

Removed the back part of the stove to reveal the wires connected to the igniter. Removed the wire nuts and removed the igniter. Reused the old bracket to mount the new part. Attached the wire nuts and replaced the back parts of the stove. Worked like a charm.

There are other descriptions here, but here's my story. I pulled the oven door off (pull straight up on it, it will come off) and removed the bottom warming drawer (there are plastic tabs on the outside of each side of the drawer--slide them and pull, several times on each side). I turned off the gas from behind the stove and unplugged th ... Read more e range, undid two screws at the back of the oven floor and lifted it forward and up. The burner is visible, but here is the hard part. The bolts holding the ignitor are underneath it and angled such that it is almost impossible to get any type of tool near them. I have small hands, and that helped. The screws are a bolt-head type or hex head, and I found that a one quarter inch open end wrench sort of fit. 6mm was too small and 7mm was too large. I managed to get the screws loosened after much struggling and manuvering, with half my body inside the oven, and once it was out, I was able to reach in from where the warming drawer was and unscrew the two wire leads attached from the ignitor to the power. They are held by plastic screwcaps. The reverse process was self explanatory, except that you should put the new ignitor in the oven and feed the wires down through the back panel, then attach the screwcaps to join the wires to the leads. Then go back in the oven and attach the ignitor, back screw first, and tighten it all the way, since you may not be able to reach it once the front screw is in. Also, use the screws that come with the new ignitor, since they are easier to start than the old ones. Tighten the screws as tight as you can get them so the ignitor doesn't wiggle, then turn the gas back on and plug it in, and test it before you put it back to gether. Mine worked, but it was a pain to do, kind of like working on an old car that wasn't designed to be fixed easily. Good luck.

I took out the racks, unscrewed the bottom cover, removed the bottom drawer, cut the leads for the igniter, removed the bad one, had a little difficulty installing the new one, the screws were a little longer than the old ones, and were a little hard to get at, rewired the the leads, and put everything back, and started it up and it worke ... Read more d great!

Turn off electric supplying appliance,then remove oven bottom plate.Remove ignitor wires from controller and oven control,then remove two screws holding burner ,lift burner from gas valve,remove two screws holding ignitor.Replace with new,and re-assemble.

Using the crescent wrench, I first removed the bolt holding the cover plate that separates the wiring from the broiler section of the oven.

Then I removed the wire nuts that connected the wires from the igniter to the wires from the oven.

Then I removed the two screws that attached the igniter to the oven.

... Read more >I then reversed the process, first attaching the igniter to the oven, then connecting the wires from the igniter to those from the oven using the wire nuts. Finally, I replaced the cover plate on the assembly.

The primary difficulty with the process was the small space to work in. One has to reach to the back of the broiler area to remove the bolt, screws and wire nuts. Some of these operations require two hands, and there's no room for both arms in this area.

However, that said, this is the third time we've replaced the igniter. It seems that it only lasts about 4 years before it needs to be replaced. It's not all that hard to do.

well,as with any repair that looks easy,i had to do a little more than what i had originally anticpated.
i was hoping for an access panel to the igniter,but after removing the lower drawer,there was only the heat shields and pans,about 20 screws later i got
to the igniter and spliced it in place,then reassembled it without too m ... Read more uch fuss -now my 93 year old friend can bake her pecan pies for charity that is her favorite hobby-thanks

Removed the bottom cover plate and the bottom storage drawer. Disconnected the burner and removed it. Replaced the old igniter with the new one. The new one required the wire connectors from the old one to be spliced onto it. Reattached the ignitor to the burner and reinstalled the burner. Tested the new ignitor before reinstalling the co ... Read more ver plate and storage drawer.

With directions from the website as well as in the box, the repair was almost flawless. I needed to be a mouse with a 6mm box-end wrench.

Removed the three screws from the top and bottom of the oven door. Removed the outside door cover from the inside door panel. This gave me access to the six screws that hold the two sections of the inside panel together. The glass of the inside oven window was manufactured without the installation of retainers to keep the window from m ... Read more oving. I installed the four retainers that I purchased. Reassembled the door. The glass now stays in place. Since there were no retainers to begin with I had to figure out how they were to be installed to prevent the glass from moving around.

Part arrived day before thanksgiving bent old igniter back and forth till broke off then easily took out screws.Cut and strip old wire, screw on new ignighter this was tough to get a wrench on with the positioning but after connecting those wires and slappin the rest of the oven back together one turn of the temp knob told me thanksgiving ... Read more was going to happen Thanks to part select I was lookin like a hero!

Removed bottom drawer removed door and racks and bottom shield.disconected two leads from igniter . then struggled to remove igniter. after ordering part readf comments from other men and the man who said he removed the burner hit it right on the head after the part arrived the very next day after ordering it i removed the burner attached ... Read more pig tails and had part installed and stove back together in 15 minutes. thanks good experience

I first read and printed out several postings on how others did the job. I read and re-read them and then I started. I cut power to stove and left gas on. I removed door, pushed back and removed bottom burner cover. I exposed the igniter which I deduced was the problem. I removed the front burner screw and the rear screws (2) and the burn ... Read more er came out very easy. I removed the igniter from the burner, made sure which wire went where (I marked them)an snipped them. I used the ceramic caps and spliced the wires. I replaced the burner and turned on the power. I turned the oven knob on and "Viola", the igniter came on and burner came to life. I replaced every thing in reverse order and called it "done". It was so easy with the postings on this subject.

1/4 inch nut driver & 9/16 open end to take the igniter off and pull the wires out of the back of the oven. Then take the wire nuts off and install the new igniter . Shove the wire nuts back in the hole. Reinstall the burner and covers. Total time is about a half hour no special skills needed. easy

Moved stove out from wall and unplugged 110 cord. Removed broken igniter from broiler with nut driver. Removed protective cover from back of stove. Cut off plug from existing igniter wires on the back of the stove. Installed new igniter and fed wires trough to the back of stove and connected the wires with the supplied wire nuts. Reinstal ... Read more led protective cover on the back of the stove. Plugged the 110 cord back in and returned stove back to the original location.

We found the part right away from the diagram provided by your web site. We located the part number easily, paid on line and received in part in two days. My husband fixed it. It was relatively easy. Saved us money to pay someone to fix it. It could easily cost us more than $200.