911619 Kenmore Range - Instructions

Pulled the three screws off unhooked the spring then removed the hinge. attached the the new hinge to the spring put the screws back in slid door back on took less than 15 minutes.

The left door hinge was broken. There are three screws that hold the hinge. It is very easy to take it out and put the replacement in

Removed burner from each one. removed drip bowl. Inserted new bowl. Replaced burner. Excellent help from order people so I got the correct bowl was irreplacable.

The plastic wheel glide that the hinge runs back and forth on was worn off on one side so it was grinding and binding.
Remove storage drawer from under oven. Open the door to the special catch position and carefully lift door off the hinges - (not by the handle, hold onto both sides).
Take out three screws w/ a hex head nut dr ... Read more iver, slip the hinge down into the hole, look under drawer area w/ flashlight and carefully unhook spring, while holding onto spring- pull old hinge out, see which hole has wear (that's the one you want to use of the three), insert new hinge all the way in and hook up spring. Pull hinge out and line up front plate w/ holes, insert 3 screws snugly. Done, awesome probably saved a 200.00 visit from the appliance guy. My husband thinks I'm amazing!

I removed the door by pulling up and away from the hinges. I then removed the drawer. I unhooked the tension spring by hand and noted the opening. I then removed the three screws on the hinge assembly, removed the ole part, and replaced it with the new one. I replaced the tension spring and slid the door back on to the hinges. I did it al ... Read more l in less than 10 minutes.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

it was hard to figure out the instructions from A switch to B switch to my switch. The first switch was no good the second one was good. prayer book didn't hurt.thank

Removed the burner elements, removed and disposed of old drip pans, cleaned the area, relaced with new drip pans and replaced the burner elements. Verified all burners were level - good as the day it was new!

I read parts select instructions and i was done in less than 30 minutes. Since 1988, this is the 1st. part that I had to replace. I now have parts select on my favorites list.

slid the range away from wall. disconnect power. removed back,compared switches and marked wires.installed new switch and wires.the adapter for the control knob was a problem it left the knob out futher than original i had to modify the plastic adapter and got it close enought! the most time spent was cleaning up the floor before putting ... Read more the range back.

Very,very easy. Just like the video described. Removed three screws. Released the spring and removed the old hinge from the slot. Slipped the new hinge in the slot,replaced the screws and reattached the spring. Job done! Great service!

I did as the video suggested.....I cut the old wires and spliced new ones already attached to the new terminal block. It would have been nice to have some instructions with the parts as I expected one piece but had to connect the wires to the new block and the new metal cover. I was guessing a bit. Also, I needed to use the holder str ... Read more ip off my old part so that it displaced the new part back far enough to insert the burner connections. That meant finding a screw and nut small enough to allow the metal cover to fit on the block. But the burner works great. I've learned that any repair requires some ingenuity.

Followed YouTube video from PartsSelect. It was real easy to do and that video was helpful. Took off door by sliding it up off hinges, disconnected springs, unscrewed hinges & slid them out - reversed to install. Worked perfect, parts were exactly right and parts came within 2 days.

Used Phillips screw driver, installed guide, applied lubricant.

Could not have been easier and I would never call myself a handyman by any stretch. Unscrewed 2 screws pulled the element out of the 2 connectors, plugged the new one back in and put the screws back in and DONE. It took less than 5 minutes and if I can do it anyone can.