911483 Kenmore Wall Oven - Instructions

I spent half an hour finding my driver set. It took about 25 minutes to turn the power off, remove the racks and element and replace the new elements.

I counldn't get the nut screw out. It wounldn't turn. Had to call a technican.

First I made sure I turned off the breakers in the circuit box that controlled the circuits for the ovens . Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. The factory wrapped a large amount of tape around the connection between the wires and the he ... Read more ating element. That took a while to get off. And I searched for heat-resistant electric tape to replace it (because, it must have served some purpose if they had it on originally). The wires hooked onto the spade connectors for the new elements with no problem. I pushed them back into the hole in the back of the oven, replaced the screws, turned the breakers back on, and it worked great from there on.

Repair was very easy-make sure you shut the electricity off at the breaker box-having the oven control off does not kill the electricty to the element . Removed the screws, pull out the element, disconnected two wires, re-attach to the new element, install the screws.

I had to struggle to get the pliers to grab hold of the screw because they were so tight. I was worried about "stripping the screws" but finally they loosened and I got them both out. My friend was holding the flashlight, so that helped. I was not real sure what to do next but the wires popped off the element so it was clear that all I ha ... Read more d to do was pop the new one on. Easy. I had the most trouble trying to get the screws out. I saved myself $$$. Thanks for your help in sending the correct part!

removed two screws disconnected old element from the two wires and replaced it with the new element. It saved $60.00 service call.

It was easy except that I had to make just a small modification to the electrical connection (holes were to small). . . . Other than that, its was a breeze to install.

.Received the part promptly. Installed it in about 30 minutes. With appliance servicemen, I figure I saved about $200.00 doing it myself. Thanks

I shut off the power at the circuit breaker. I loosened the screws securing the baking element to the back wall. I then pulled out the baking element toward me and found the wire leads bolted using self-tapping screws to the original element. Since the holes on the mounting tabs did not take the old screws, I had to drill out the holes on ... Read more the tabs of the replacement element. After securely bolting the leads to either terminal on the element, I had to drill two holes on the back wall for the mounting plate of the new element. Then I used the cordless drill with the Philips bit to drive in stainless steel self-tapping screws (not zip screws) to secure the element to the back wall. I turned on the power at the circuit breaker and reset the clock (mechanical).

Needed to drill two new holes for fastening the element to the oven wall. Change in design. Enlarged the holes in the spade connections since I was unable to find smaller bolts than 4-40.
I would suggest to make the holes in the spade connections larger.
The change out was not a problem.

Upon reciept of the replacement door glass, I removed the door from it's hinges, removed the eight set screws from the exterior housing of the door, removing the interior heat shielded portion of the door, cleaned any glass residue from the area installed new glass reinstalled interior portion of door inserted screws tightened and replace ... Read more d door on hinges.

Ordering and shipment of the part were quick and easy. The price was excellent too. It was the easiest repair we ever had to do to an appliance. After removing the screws that held the element in place and disconnected the part, my husband immediately connected the new part. It took less than 15 minutes.

removed screws; cleaned out broken glass; insert new glass; screw back in

turn of electric oven, removed screws and took out old element and put in new element and replaced screws. done simple and easy

Turned off power. Removed two screws. Took out old element. Used pliers to remove connectors. Installed new element. Set screws. Turned on power. Works.