911463 - Instructions

Flipped the breaker. Removed shelf, Find the right size nut socket, unscrew the two screws, pull the element out a little bit, disconnect the wires (on pretty tight), pull out element, clean out any mess in the oven, compare element with new one to make sure its the same size and such, connect wires to new element, replace screws, fl ... Read more ip breaker back, turn on for a few minutes to make sure it works. Piece of cake.

First I searched this site and read about the repairs - which made me feel like my husband could do it with ease. Then he removed two screws inside the oven, removed the broken element (didn't know it was broken til removed) and replaced the new one - just like that! The real key was being able to read how it was for other people who ha ... Read more d already done it. That's the only reason I'm submitting my storey. Thanks

I turned off the power to the oven at the breaker. Then I removed the two screws from the old element, pulled the old element out about 3 inches and disconnected the wires from the element and installed the new one.

This was really easy, and pretty with no problems or issues It took me longer to write this than to do the actual installation. I used a digital camera to help me remember where things were, but a pen/paper works fine. Here's what I did:

1. Turn off the breaker for the cooktop.

2. Remove (2) 1/4" hex screws directly ... Read more under cooktop. You may need to open oven door to reveal them.

2. Prop up cooktop. I used the box the replacement element came in.

3. The element is held in place with (3) brackets held in by a #2 philips screw each. Mark the location of each of the brackets. There are numbers on the element to help you do this.

4. Write down where each of the wires connects to the element. There's only a few of them, but I tend to forget that stuff. The wires have female spade-type connectors that connect to the male ends on the element.

5. Using a needle-nose or small pliers wiggle each wire off the element. Grab the wires by the end of the female connector when you do this. I found it helpful to use a small flat screwdriver to help pry them off. Mine were on pretty tight, so expect this to take a few mins. If you have problems getting to the wires, remove the brackets (next step) first and come back to this one. I let the element hang from the wires without any problems, but I still wouldn't recommend it.

6. Remove each of the screws with a #2 philips screwdriver. Support the element with your hand and gently pull each bracket away from the element. Once they're all gone, the element should just come out. I took a look at my old element and saw that the large burner wires were melted in a couple places, so it was definitely broken.

7. If necessary, clean the underside of the cooktop surface with a clean papertowel. There was a little dust from the old element on mine.

8. Connect the new element and test to make sure it works by turning on the breaker and turning on the burner for a second or two. Note: This will make the top of the element hot for some time, so test it and go away for a few mins. If it works OK, proceed. If not, disconnect and figure out what else may be wrong.

9. Using the old element, make copies of the marks you made for the bracket locations onto the new element. You'll have to punch through the insulation when re-attaching the screws.

10. Re-wire the new element, if necessary and re-attach the brackets over the marks you made. This may be a pretty tight fit because the new element was thicker than the old on mine. I opened up the brackets a bit to make it not so hard to re-attach. Hook the brackets on and squeeze them over the element. The holes in the brackets need to line up with the holes drilled into the bottom of the element. If they don't, spin the element around (or detach and re-attach the brackets) till they do.

11. Screw in the (3) screws over the brackets pushing them through the insulation on the element.

12. Close the cooktop and reattach the hex screws under it (1/4" hex).

13. Turn on the breaker and test again.

Thats it, works great now. Good Luck

Removed 2 screws that hold element and pulled old element out about 2 inches to disconnect the wires from the old element. Connected the new element and remounted to rear oven wall. Very simple and saved a visit from the appliance repairman.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires
the repeated the process to complete the installation.
Relly easy.

TURNED OFF CIRCUIT BREAKER. Removed nut, washer and screw, pulled out electric burner about three inches, disconnected electric terminals and removed damaged element. Inserted new element into oven, connected electric terminals, pushed electric prongs back in, screwed element to back wall of oven....DONE Easy as 123

Repair was very simple. Removed 2 screws under the cooktop, tilt the cooktop back, unplug 4 wires from 8" burner, remove two screws holding retaining clips, install new burner in reverse order. Very simple!

Open lid,un screw coil,pop in new coil snap holders in place,then cook a steak

I opened the lid, and found that the terminal blocks were burnt, the wires were melted. I ordered one set of terminal block to replace the burnt one, and it worked. Before I started, I shut off the electricity in the whole house to be safe.

Replaced High Voltage Diode. Very carfully due to the extream danger of a electrical shock.

The existing terminal block on my Ge oven/Range had melted due to a loose wire causing sparking and starting the plastic casing of the terminal block on fire and melting it, Part select made the part easy to find and had it at my house in 2 days. All I had to do was remove six screws to take the back sheet metal cover off of the oven. U ... Read more nscrew the terminal connections remove two mounting screws that held the terminal on to the oven body. This was a little trickier than it should have been because the melted plastic had reformed making it very hard to access the mounting screws. i then mounted the new piece and plugged the oven in, it took 15 minutes and was very easy. definitely saved me at-least a $100 for the service call i would have made if finding the part wasn't so convenient

First I removed the door by lifting it off the hinge assemblies.

Then I removed the drawer to access the spring.

Removed the spring, noting which attachment hole was used.

Removed the hinge assembly with a Phillips screwdriver.

Replacef the unit.

Repeated for the other hinge assembly. ... Read more

Note: it took longer to find the correct parts in the parts diagrams than it did to replace them.

The outer ring on the adjustable large haliant surface burner of our smooth top stove would not work. It would only work on the small (inner) size.

Found the part on this site, ordered, 3 days later, and it was fixing time.

2 screws removed to lift cooktop, 2 screws to remove old burner and disconnected 4 electric ... Read more clips one at a time and placed them in same position on new burner. Replace the 4 screws and done.

VERY SIMPLE.

Unplugged range. Opened oven door and removed two screws from top of oven opening. Lifted oven top and propped up
with a 2 x 3.Unscrewed the two screws that were holding