9114556 Kenmore Range - Instructions

Cut 4 inch’s off the new terminal block wires then using my wire strippers stripped 1/2 inch off the ends , the old terminal block wires I stripped 1/2 inch at the ends using a wire nuts on both wires and electrical tape connected the terminal block to the stove plugged the new burner in and the burner worked 100%.

replaced lights in refrigirator and freezer

I just follow Steve's Installation Vidio. My range works.
Thanks Steve

twisted it in place

First pull knob off switch. You may need a small screwdriver to gently start it. I then removed two screws, one in each end of control panel. Then rolled the panel up and out, as it is kind of hinged in the back. Removed two screws from switch front,layed it to the side and installed new switch. Removed wires (there were 5) one at a time ... Read more with needle nose pliers, and placed on new switch. Replaced panel screws and was finished. Easy fix, quick delivery of part, I have used Partselect in the past and will continue.

With multimeter checked resistance of oven sensor. Specs called for 1100 ohms. It was off by 27 ohms. The sensor from Part Select had exact wire connection as original. Then just matter of undoing old and reconnecting with new one.

One unsatisfactory event. I asked Part Select why my clock did not work or light up(timer ... Read more works ok) . Answer was: sorry we have no time to help you. That soured the otherwise happy experience.

repair went fine, real easy.

The customer service rep was brilliant in finding the
right part number! It was sent the following day
(with email to let me know) The part itself was just
exactly like the old one. I simply turned off the power,
removed the 2 metal screws and unplugged the
broken element. The new one fit properly and works
... Read more />like a million dollars. For about $50, you made me
look like a hero in my own house! Thjank you

Pull out oven and unplug from 220 outlet. Remove rear upper/lower cover (4 screws), Remove two wires from rear of element. From front, open oven door, remove two screws and pull out old element.
Install new element by reversing above sequence. Then test and push oven back in place. Easy!

First turned off the power to the stove at the breaker panel, thenI removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Disconnecting/reconnecting the "clips" was the only difficult part because they did not slip off/on easily. Replaced the element in the ov ... Read more en, replaced the screws...good to go!

Best part of buying from Parts Select was that they shipped the part the same day I ordered it, which was the Friday after Christmas. Competitor would not have shipped till the following Monday and we needed the oven ASAP!

I unscrewed the two screws inside the oven, then i pulled the oven away from the wall and unscrewed the protective shield, and undid the wiring. Then i removed the element. Once the new one arrived, i pretty much just did the same thing in reverse. vwa-lah... fixed!

It took a nutdriver to remove two nuts. The defective element was removed and the replacement installed. It works great!

Flipped off the circuit breaker first. Unscrewed the two screws holding the element in place. Pulled out about 4-5 inches. Tried several times to pull apart the connections, finally got 'em - don't give up (I must have weak fingers). Then plugged in the new element, shoved the wires back in, screwed it back in place, flipped circuit br ... Read more eaker back on, turned the oven on.... made brownies (o:

i slid the oven out unplugged it !! , removed back cover with a nut driver, removed the two retaining nuts from the old bake element ,opened oven door removed two nuts that hold bake element to the back of the oven , installed new bake element then attached wires in the back of oven to the new element re installed retaining screws inside ... Read more oven , check to make sure screws that hold power cord wires to the over are TIGHT !! i then installed rear cover then plugged in the oven it worked great !!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires,held wires one at a time so tehy wouln't slip back into rear holes in oven, slid off connector tabs and pushed on to replacement unit...)