9114556 Kenmore Range - Instructions

remove two screws slide out. slide new one in. put two screws back. done.

First and most important trun off curcit breaker. Use 1/4 inch but driver to remove socket (2) screws. Remove ground and hot wire clips from old socket, replace on new socket. Screw back into oven ceiling and turn on power. Reset clock and your are done. Very simple.

This electric stove has a lift up top which I lifted to get at the block and follow the wire back to the terminal at the back of the the stove. I removed the 5 small lag screws holding the back in place, removed the backing followed the wires back to where they connected in the Stove On/Off Control, disconnected the two wires from the co ... Read more ntrol and then laid the new part in place rethreading and reconnecting the wires. I reinstalled the block and ran a test to ensure the burner operated correctly. After successful testing I disconnect the old block holder by removing the small lag screw, replace it with a new one that came with the replacement terminal block. I then inserted the block into the new holder carefully rolled up the excess wire and wrapped it in a couple of places with electrical tape and also secured it to the side of the stove, out of the way of operation with electrical tape, put the top down, plugged it back in and put it back in place. All told the repair took about 40 minutes. I was impressed with the speed of delivery, the quality of the product, the instructions for installation and the added bonus of getting a terminal block holder as part of the repair kit! Thank You for making me look like a genius!

Disconnected the old socket ( 2 srews ) removed the two wires from the old socket, reconnected them to the new socket and reinstalled the lamp.

Unscrewed the heating element from the inside back of the oven and removed the housing cover from the back of the stove to access the terminals. (The unit had arked and fused the terminal to the connector.) Installed the new unit and replaced the housing cover on the back and screwed the unit into the back of the oven. Works like a charm ... Read more .

Switching out the part was reasonably easy. The hard part twas that over 15 years some of the other parts have dried out. The oven indicator light came loose and the tabs on the clock were broken. With the help of some glue & some Z bracket it is back together minus the oven indicator light. Not perfect but cheaper than buying a new one.

First I unplugged the stove. I then removed the control panel using a flat head screw driver. Then I removed the two screws (phillips head) holding the element in. Five wires had to be disconnected from the old element and placed on the new one. As I removed each wire from the burned out element, I placed it in the same place on the n ... Read more ew one. I then replacedd the element on the stove and put the control panel back in placed. I plugged the stove into the wall outlet and tested the element control. This whole procedure took no longer than about fifteen minutes.

Unplugged the Range and removed the two screws holding down the cook top. You do not need to remove the vent chamber at the rear of the range since the top lifts up about 4 inches. This should be enough room to get your hand onto the plug going to the door switch. Pull off the plug and remove the swich. Pop in the new one, put on the ... Read more plug, reinstall the two screws and you are done!

Read the thread on "burnt smell" and DO NOT assume it is a burned out element. Follow your nose!!

unscrew the terminal block,pulled the old wires out,installed the new wires installed the new block

Followed the video directions on your website - GREAT INFORMATION. Everything went very smoothly It took me longer to find my work light (after turning off the electric to the oven) out in the garage than it did to complete the repair!! SUPER PLEASED - WOULD NOT HESITATE TO RECOMMEND THIS COMPANY TO ANY DIY ADVENTURER!!

0) Take the back cover of the range off.
1) Carefully noted how the wires and the sockets were connected.
2) Visually checked that the new parts were practically identical old ones.
3) Put together the new sockets from the parts in the kit.
4) disconnect the old sockets and put the new sockets in place.
5) For eac ... Read more h unit disconnect one old wire at the time and connect the new wire. Repeat the same for second wire.
6) Neatly bunch together the rest of the wires with electrical tape. Do not cut the wires!

That's it! It took about 20-30 minutes.

pulled out the stove,,unhooked the power cord from outlet. I then pulled the control knob off and removed the the six screws from the back panel. I then removed the two screws the were under the knob and removed switch from panel..I unhooked the wires one at a time and rehooked them to the new switch,,pushed the switch back in the panel a ... Read more nd installed the two screws. The knob was different from the shaft on the new switch so I took my dremel and contoured the shaft to fit my switch. I plugged the stove back into the outlet and it worked perfect..

I have a double oven and coincidently I had to replace the two Oven Light Assemblies.
I am really glad about your web site because once I got the number from my oven model you guys were the first ones that came up. Thanks to your prompt and reliable service my oven is back to its original state.

Jose Figueroa

I pretty much followed the youtube video posted under the part that I needed. Turned off electricity to that area of the house. Unplugged stove. Took out the old sensor, pushed new sensor cord through the back hole. I did put a small amount of tape,so I could pull it through from the back better. It was impossible to get the clip discon ... Read more nected in the back and the new clip didn't match up correctly anyway. Ended up having to cut the wires and strip them. I twisted them together and put on the ceramic wire nuts on. Reversed ever thing I did and F3 appeared. Looked that code up on internet. It was from an open or shorted oven. Suggested I check the connections. Pulled stove out again, unscrewed caps on wires and noticed the sensor's wire had another cloth type coating on it. I gentle cut that off, twisted and capped wires again. Plugged in oven, turn on electricity, and tried out stove. Everything is working just fine. Everything took a little longer because this was first time doing this type of repair.

Watched the video on the PartSelect site. Could not have been an easier repair and I saved the cost of a service call - probably saved at least $100 - $150 in service call and I can only guess what the labor cost would have been. Will use this business again for other appliance repairs on my older stove, washer, etc. By the way - the o ... Read more fficial Kenmore site said this part was no longer made and unavailable --- Thank you PartSelect for having the part and saving me the cost of buying a new stove!