911436 Kenmore Cooktop - Instructions

After months of buying the wrong parts & cost I discovered this site So easy to order & quick delivery, plus very easy installation. Thank you. I also wanted to add that the reps (Tanisha & Matthew) were extremely helpful & informative. I can only hope all the reps equal their performance. I will definitely be using this site, before an ... Read more y other source. Knowledge & cost is also important to me & that need was met. Good job!

Ever the optimist, I'd replaced the burner on this relic of another time to no effect. That left the switch. You guys should know that when a burner element goes bad it can take out the switch. I should have put a meter on it. Wehn I looked for a replacement a few months ago there were still factory parts available, but they were $80 or s ... Read more o and I wasn't inclined to risk that on a 40 year old range. I offered to replace the raange for my daughter as a Christmas present but she like this old thing. It was an unusual size with a pan storage compartment on the left. I went on line and found this universal replacement for about $25 delivered. What the heck. I ordered it and it arrived within a week. I pulled the stove out, killed the breaker, pulled the knob off, used a nut driver to take ther rear panel off, two phillips screws under the knob hold the switch in. The terminals on the old switch are in a slightly different order but are clearly marked L1, L2, H1, H2 and P. The P is the power and has a smaller terminal so you can't put it on the wrong one. Just examine the old switch ( it was marked the same way) take off the L1 and put in on the L1 of the new switch and so on, make sure you use the correct knob adapter to fit your old knob and break the switch stem to the correct length. It will break easilly if you hold it with one pliers and break it with another. Screw the new switch in place with he old screws. At this point, I closed the breakers and tested it. It worked fine. I turned the breakers off again. Buttoned it up and slid the stove back into place. 20 minutes tops. Great product. Good for another forty years.

Basically removed the screws holding the op on and removed the vent from back. Just "figured it out" and now it works. Wish I could be more helpful. Recommend moderate experience and confidence.

1) SHUT OFF POWER
2) Removed the cooktop from the counter
3)Remove 6 screws holding the cooktop glass frame to the housing
4)Removed 4 screws holding the switch retainer to the housing
5)Removed 2 screws holding the switch in place
6)Moved one wire at a time from the old switch to the new switch
7)Reassembled

Disconnect power. . . Remove control panel, pull wire connectors,[note location] remove old switch, install new, install wires, snip stem to length, set knob . . . Turn on power - works. [Note this is a live part even when not connected]

First removed the back of range, then the metal vent section that prevented the range top from lifting up. There are 2 screws accessable only after you open the oven door that need to be removed before you can lift up the glass top. Then remove the bracket holding the 2 front heating elements. Made a diagram of all wires going to and fr ... Read more om the large 2 element heater. I had to use an adjustable wrench to remove the 2 studs that were screwed into the sheetmetal section of the element. Carefull not to let the springs or retaining washers get lost.
I examined the inner and outter heating element windings and discovered that the old and new unit was not wired the same. Additionally the instructions were not very clear as to what color wire they said to cut and why. I could not install the studs in the exact locations as the original unit since trhe new one had a slightly different terminal block location. This resulted in the new unit being rotated about 20 degrees CCW looking from under the top. The wire going to the LED heating indicator was now too short so I used the wire supplied with the new unit to extend this.

I used a multi-meter to verify the coil terminal locations and made sure the colored wires went to the same terminals as the original assembly. (Inner coil, outter coil and common terminal) The instructions supplied did not show the same terminal locations as the unit itself for these 3 terminals. Other terminals, which were simply junction points, were the same as the original unit.



By using an ohm meter and the diagram of the colored wires made before taking off any wires one should be able to do this repair. But it was not easy. Ckeck all wires 3 times before turning on power.

1. Bought replacement part said to replace old switch.
2. Pulled old switch out.
3. Replacement part did not match. Would have to take entire switch panel apart to change to this part.
4. Multiple-part instructions very poor. For my switch unreadable.
5. Old part was "push to turn". New part was not.
6. Knob did ... Read more not fit new switch. Old shaft was "D" shaped. New is square.
7. Gave up. Need to call repair shop.
8. Hope this helps.

The first thing was to watch U-Tube . The replacement burner was being
replaced in a GE glass top range. Exter tools were required than depicted
in the U-Tube project. The project overall was not dificult for me however I was a general contracter for over 25 years

1- opened oven door
2- unscrewed 2 screws underneath top with a socket wrench
3- unscrewed clips that held burner
4-used needle nose pliers to pull off wire clips off old burner
5- placed wires onto new burner
6- opened clips to make it easier to reinsert burner
7-reattached burner
8-Replaced top
... Read more r />The hardest part was unscrewing the 2 screws that held the top in place due to the position of the screws

Read less