911322 - Instructions

Used scribe to remove grate foot plug still in grate inserted new foot.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. . . ) It was like drinking juice

First remove the screws around the inside perimeter of the door. These require a special hex driver. Take off the inside plastic liner of door.
Peal off the old Insulation Foam Strip and replace it with the new strip in the same location. Make sure the wires are off to the right side. Replace the door plastic liner. Done. The In ... Read more sulation Foam Strip really acts more like a loose gasket to keep spashing from creeping under the door and drippin out on the floor.

I ordered the spark module and replaced it which was veru simple, plugged it in and it sparked only now and again. I finally said forget it and it has now stopped sparking but for how long I do not know.

TURN OFF GAS and unplug stove. Removed burners (used screw driver to remove screws) and spark ignitors (used pliers). Lifted top cover of stove and unpluged the harness assembly(pulls out easily). Inserted new harness and replaced cover. Replaced burner parts included new spark ignitor. Plug power cord and turn on gas.

Repair was easy once I got the correct part. When the parts were listed as small and medium large I thought they were talking the diameter of the bowl. It turns out they are talking about the center hole in the bowl. So I needed one small and three large. Everything great now.....stove looks great and clean.

Good way to tell/verify what your problem is. On my GE Cooktop, moving any of the knobs to light cause a spark for all igniters. One of our knobs would not cause a spark. - Remove gas grills and covers. - Remove screws - Pull igniters up (be gentle to not crack them - Pull wire out from igniter - lift cover of cooktop - pull harness off ... Read more each know and disconnect two wires - put new harness on and connect and backfill. Pretty easy overall.

Easy to replace - caution to make sure spark igniter switch is aligned and secured in correct position on the gas valve. The switch should cover both mounting screws on the gas valve when properly installed/aligned

This was and always will be an easy fix, all I have to do is get my ice pick and pick the broken rubber part stuck in the hole if it does not break clean and fall out. Not much more I can say about this simple problem.

put it in but it keeps falling out. they're made narrower than my oven grate.

I used a hex wrench to remove the 8 screws ( 2 on each burner ), pulled up the knobs, and lifted the ceramic top. use pliers to disconnect the spark plugs. I disconnected the switch harness from the igniter, disconnect the igniter wires remembering the color scheme.My igniter had a minor variance from the old one which an acompanying map ... Read more clarified. I installed the new switch harness and the new igniter, made the igniter connections according to the color scheme and the accompanying diagram, replaced the ceramic top, pulled spark wires thru, installed the burners and the spark plugs, tightened the 8 screws, and tested the burners.

Ordered by phone parts & very pleased with all of transaction.

Simply removed the 9 T9 screws from the top of the cooktop, removed the igniter spark modules, lifted the top of the cooktop up and removed harness assembly. Unplug harness from spark module and replaced in same fashion. SUPER EASY done in less than 15 minutes

Cut off power to the cook top and confirm that power is actually off. In my case, this involved turning off a cicuit breaker. Remove all burner control knobs by pulling straight up. Lift off all grates, burner caps and burner heads. Remove two phillips head screws from each burner bowl. Pry each burner bowl up and unhook the ignitor ... Read more wire. I labeled the wires to make sure I got them hooked back up right. Remove the four burner bowls by lifting them off. Make sure you remember where each goes so you can reinstall them in the right places. Pry up the glass cooktop and lift it off. I took the cooktop ouside and gave it a good cleaning. This plus cleaning around the cooktop and cleaning the burner bowls is what took most the time. Lift the defective switch off and disconnect the two wires. Align the flat in the new switch to the off position. Reconnect the wires and install the new switch on the valve stem. Reinstall the cook top. Reinstall the burner bowls making sure to reconnect the ignitor wires. Reinstall the burner heads, burner caps, grates and knobs. Turn the power back on and make sure everything works correctly.