8543 - Instructions

Followed electrical drawing from switch to motor, Thermal fuse was in the line and no power coming through it, removed wire and put together and tested, dryer turned on. Read statements from others at parts select and also bought thermostat because time stopped working last year. Installed both parts and cleaned dryer, works perfect inclu ... Read more ding timer.

I first disconnected the power. Then, I took off the back panel with about 8-10 screws. There were a couple of screws that held the heating element in place, which I removed. Then, I disconnected the heating element. The heating element was toward the bottom right hand side and was easily accessible. The connections to the heating element ... Read more were a little bit tough to disconnect but not too bad. I had to use a flat head screw driver to kind of pry them off but looking back I think some needlenose pliers would have worked better. I then removed the bad heating element and plugged in the new one. I replaced all the screws and turned the dryer back on. It blew hot air again and all was well. I am not very mechanical and it was all pretty easy.

Grow a second set of hands. Always unplug any appliance. Remove lint screen. remove two screws (philips Head). I took a wooden shim lightly tapped w/hammer to pop front of dryer top free. Mine worked on hinges and just flipped back til it rested against the wall. Removed two 5/16 screws inside holding face on carefully raise face section ... Read more off the support clips at either side on the bottom. Pull drum out (I have the large style drum commercial size [approx.). Clean the inside free of all lint (known to be fire hazard). Sling new belt around drum. Get newly grown set of hands to hold drum in place. Pinch belt to fit between tensioner, lift tensioner and place belt around motor pulley. Spin drum couple times to make certain belt isn't twisted. Reverse dismantle proccess to put back together. Replace all parts that come with kit, you'll feel better knowing you got a new dryer, almost.

1. Unplug dryer from power outlet
2. Lift dryer top from front (hinged in rear). Just friction holding top down. Use flat scewdriver wrapped in cloth to help lift.
3. Locate heating element - rear top behind drum
4. Unplug red wires to the high limit thermal fuse
5. Unplug red wires to the heating element
6. Unlug ... Read more white wires to the high limit fuse
7. Remove high limit thermal fuse
8. Remove heating element
9. Remove high limit fuse
10 Clean heating box
Installation is reverse order but do the following first!
Clean lint trap - Remove front of dryer
1. Unplug white door switch wires. inside front top right
2. remove two screws securing the front of dryer - inside front top left and top right. Front of dryer is hinged at bottom
3. Clean all the lint you can find. If you have never cleaned out the lint, there might be a lot and the cause of over heating (shorting fuse life). Add to your yearly things to do list.
4. While your at it check the alignment of the plastic glides the drum sits on.
5. Also check the foam gasket between the fan housing and lint trap. Mine was off a bit. Realigned with doubled sided tape.

There was no problem with lint build-up within the dryer & the exhaust vent. I removed the gas cycling thermostat & thermal fuse from system & dryer still was not operating correctly. The radiant sensor & hi-limit thermostat both seemed to be operating correctly. That left either of the two coils as the culprits. I replaced both coils ... Read more & the problem was corrected.

took a couple differant parts to fix the dryer. i ordered one part at a time. i was expecting to wait the 5 days for shipping but i got home from work the next day of odering parts and they were there waiting for me on my doorstep. all three times i ordered. this website is the best site to order parts. i wont go to another website or sto ... Read more re if i need to order parts for appliances. u guys have my business for life. thumbs up.

When my dryer suddenly stopped functioning, without any prior signs of pending failure, I guessed that it had to be something simple, like a fuse. I did a google search and stumbled across a forum post that described the symptoms (wouldn't turn on), and the poster said that Whirlpool recommends replacing the thermostat whenever the fuse ... Read more is replaced. The reason for this is that the likely cause of the fuse burning is that the thermostat is no longer properly regulating the temperature range of the heating element.

I disconnected the power source, and then I removed the back cover, and both parts were in plain view, so I simply replaced the wires one by one.

First I called an appliance repair place. They charged me $40 to come out and said "the air vent might be clogged". I snaked it out and really wasn't anything in there. So I started thinking it might be a thermostat. After reading the reviews that others posted here, I said, "how hard can it be"? Thanks to PartsSelect putting a diagra ... Read more m (schematic) of the parts, I could see what I was looking for when I removed the back panel. So I took my nutdrivers out, disconnected the vent hose and removed the 10 or so nuts off the back panel & got it out of the way. Took out the vacuum cleaner and sucked all the lint out. Removed the housing where the heating element was and marked on both thermostats and housing where each wires went. As cheap as PartsSelect had the thermostats priced, I figured why not remove the guesswork by buying the highlimit and cycling thermostats and a new heating element too. One screw in each thermostat and out they came. Swapped wires with new thermostats and put them back. With the heating element...it was all one piece, so no fighting to get the element into an old housing. Just swapped them. Put the back panel on and reconnected the vent hose. Cost to repair: about $100. Time for parts to get to me: 2 days. Time to install new parts: about 10 minutes. Knowing that I have a dryer that runs like new AND saving a TON of money on electric bill....THAT is priceless. Thanks PartsSelect!

I can't believe I waited so long to find this part and do this. I got the package very fast, opened it, took the piece to my dryer and popped it into place with my fingers. It worked perfectly! this took all of two minutes and saved me from having to hold the dryer door closed with a stick. Thank you, thank you!!!

I spent nearly an hour trying to self-diagnose the problem before I wised up and found PartSelect.com. After reading just a couple of postings I went back and tested the thermal fuse. It was bad. Other posts suggested I replace the thermostat at the same time, so I ordered both. The parts arrived within three days and the actual repai ... Read more r took less than 10 minutes.

unpluged the dryer, removed the back panel, I examined the heating coil, it seemed unbroken, so I used a amp meter to test the various sensors. Found the upper thermal sensor was bad, looked up the part and ordered it, had to get the thermal cut off kit to get the sensor I needed. Installed it no problem, put the back back on, and it work ... Read more ed great.

First, I replaced the heating element which was super easy but I still didn't have heat - frustrating! I then ordered the thermal cut-off kit and thermal fuse. I replaced the thermal fuse and still no heat. Then, I took one of the fuses from the kit and replaced that and finally got heat. There was another fuse in this kit that I still do ... Read more n't know where it goes but right now I don't need it. Had I known (by a volt tester) this would have been super easy to fix, but I didn't have one so it was trial and error. I did find out, however, that if the heating element goes it usually takes the fuse with it. The fuse I replaced (that finally gave me heat) was located in the casing just above the element. I hope this helps!

Timer wasn't working on the regular cycle so I replace it with a new one from partselect. It still wasn't working so I ordered and replace the cycling thermostat, the thermal fuse I also cleaned the vent and dryer it still didn't work so I read the diagram for the electrical and found that a coil for the gas valve is line with timer. I or ... Read more dered the coils for the valves, replaced both valves and tested the dryer and it work just like when I first bought the appliance.

1. Removed the screws from the lint catcher
2. Removed the bolts from upper rear of dryer
3. Pried off the dryer top from the front (it rests on rear hinges)
4. Disconnected dryer door wiring
5. Removed bolt from inside upper front corners; removed front panel (be careful: the edges are sharp and the tumbler will fall ... Read more when it loses support)
6. Removed broken belt and lint from interior parts; removed tensioner (which had fallen out of place). Note: The newer models have a tensioner pulley; my older model had a smooth semicircle that was confusing at first glance
7. Flipped dryer onto its back (for easier reinsertion of new belt and tumbler)
8. Placed new belt on tumbler; reinserted tumbler
9. Inserted new belt through tensioner, inserted tensioner "legs" into grooves on floor. Note: The belt will pull the tensioner upright when it's inserted properly (which isn't obvious at first)
10. Made sure belt and tumbler seal were properly installed
11. Replaced parts in reverse order
The process took over an hour because I couldn't figure out how to insert the belt through the tensioner. The trick is to insert the folded belt through the tensioner and onto the motor pulley. If I had to do it again, it would take about 30 minutes (including cleaning lint)

After realizing that my dryer was no longer heating, I took off the back and examined the heating element. I saw that a coil was broken and knew that it needed replaced. When the part came in, I basically changed out the wires that were plugged into the old element on to the new one, replaced the screws in the heating element housing an ... Read more d back panel, plugged in the dryer and was back in business! Oh, by the way...I am a 49 year old WOMAN!!!!