8507 - Instructions

Had to defrost the freezer which takes most of the time. Once freezer is defrosted its a simple matter of disassembling and removing the cover which covers the evaporator and disconnecting the defrost thermostat and replacing with the new one then reassembling. The information provided at the Parts Select site was all I needed to get th ... Read more e repair done.

I removed the nuts that held the motor mount, then removed fan blade, cut the wires, and slid the motor pass the mounts and the coil shroud, Installed motor in reverse order. worked out ok.

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new ligh ... Read more t bulb in was not the problem.

Removed rear cover to see non-operating fan - removed three mounting screws on the motor that were a challenge to access. Swapped fan from old motor onto new motor - one threaded nut on the motor shaft. Spliced new fan wires into fan wires of the wiring harness and mounted with three self-tapping screws supplied with new fan motor. Repl ... Read more aced rear cover and plugged it in! Now the refrigerator cools like new (1981 model side-by-side Admiral)

remove frozen food. take back panel off. use hair dryer to dethaw finned part. swapped defrost thermostat.one lead ok, other had to cut ends and wire splice together. replace panel and food. took care of problem, food in fridge stays cold. totally impressed with delivery time. ordered mon here tuesday. awesome..........

Pulled out the refrigerator and removed the two panels from the rear of the refrigerator. Removed the fan held in by four screws and unplugged the connector. Soldered on the original connector, installed the fan to the motor and re-installed the unit into the refrigerator. Then blew out and vaccumed the condenser coils.

Just as others discribed, removing ice maker, defrosting Freezer, removing freezer basket and shelf, removing the back panel, locating the iced over thermostat. One of the connectors wasn't the same, so I cut off the connector and wire from the old thermostat, spliced the wire and connector to the new one. Used heat shrink to cover the ... Read more splice. Reassembled everything. :-D

I used the original connector from the spent thermostat and waterproofed the connection with a 16g wire nut and electric tape. Works great! In hindsight I would have ordered the part earlier as this is a typical solution to a freezer frosting over. Manual defrost is a pain!

A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.

Remove trays and front drawer (2 screws, probably optional, but but easier to work with it removed). Remove the icemaker (2 screws), disconnect icemaker electrical connection. Remove back panel (bunch of screws). Once there, I heated up the coil to remove all the ice so I could get to the thermostat (it had become very clogged from not ... Read more being defrosted). Remove and replace the thermostat, then put everything back. Now works perfectly.

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

I noticed that the refrigerator was having trouble maintaining temperature. Thought it might be time for new one until I found out that a new frig was $5k to $7K. Just happened to notice that the light switch didn't look quite right (was not sitting sqaure to the door). Once I pressed it it came loose. I then realized the the lights we ... Read more re staying on (50 watts of heating). Replaced the switch and the frig started working like new.

very easy

Screwed in light bulb and glass protector

Used a screwdriver to pry loose the old switch, swapped wires to the new switch and pushed it into the opening. Took about 2 minutes.