8351 - Instructions

Turn off power then turn to take old burner out ,
disconect 2 wire , .
Connect electric wire with new burner press in then turn and clock . Turn power on then start stove
and check .

replace burner-had to hit old burn with rubber mallet to break off grease and took old burner off-two wires were connected to it..put those on new burner and was done--have a little problem--flame is lower now than it was-but it turns on

find the part (image is really helpful), buy, and replace. Like I said, it's really easy.

I replace the igniter first that didn’t work so I had to order the wiring and then I replaced that there was a cover that I took off with a screwdriver took the wiring off and put the new wiring in it it was that easy.

No repair involved. Just replaced a melted burner knob.

This is the second repair to this stove-- A few years ago I went to Parts Select to find a new light panel, and that repair went perfectly. So when we re-did the kitchen I decided that the old stove would look fine so long as we could find some new grates. Custom-sized, nobody had them, but your company found them and shipped them quickly ... Read more . We thoroughly cleaned the stove and PERFECT! This is a good way to keep stoves and other appliances out of the landfill!! I love it.

Your site was easy to navigate, which made determining the problem from other customers easy, and choosing the correct part to replace the malfunctioning burner.

The malfunctioning burner was easy to remove by twisting it a quarter turn counter clockwise, removing the two wires and replacing it with the new burner cap with el ... Read more ectrode.

Our handyman took off the burner caps and checked after we reported smelling gas. We ordered the replacements here, and they arrived by only the 2nd business day, instead of 3-5 as expected. The only hard part was scouring off the rust, with SOS pads, from the stove top before putting on the new burner caps (a simple plug-in)!! This is ... Read more very important to check on your stove; you could blow-up your house! The gas was escaping under the old burner cap, through the rusted-out portions.

Used strap wrench to turn out. Rust build up under the burner. Used flat screwdriver to loosen under burner and strap wrench to turn out. Then replaceing the igniter was very easy.

Removed and replaced old burner. ck'd ok.

cut off terminals and replaced with the right size one's stove lights every time now wlrowe

The trickiest part was locating the elusive spark module. I am not certain I took the best route, but not considering all the wrong routes in trial and error, it was the most expedient. Certainly there must have been a single something to remove to get to this frequently faulted part..

Anyhow, thanks to the great part, the st ... Read more ove works really well again.

I ordered the two replacement burners. When they arrived I equipped myself with WD-40 spray, rubber mallet and a rubber gripper I used to use to open canning jars. Sprayed the WD-40 around the burner base and let it sit for 20 minutes. Made a mental note of the location of the sparker of the burner, to remember to put the new one in the s ... Read more ame way. Gathered my courage and gently wacked the burner with the mallet all around it. Then grabbed the burner with the gripper and gave it a firm ¼ circle twist counter clockwise. It came apart with no problem. Disconnected the two electric wires by slipping them off their sockets. Removed all the loose rust and cleaned around the burner. Reconnected the wires with the new replacement burner and dropped it in its place. Wiggled it a little until it fit back into its original location and twisted it ¼ circle clockwise. Done, just saved myself the price of a new stove! Note: There is no need to shut off the main gas valve.

First I turned the burner head counter clockwise, lifted it out and pulled the connectors off. Then I connected the connectors back on the prongs of the new burner head and placed it back on the gas line and turned the burner head clockwise. I then turned the pilot light and and tested the connection. It worked without any problems. I the ... Read more n proceed to replace the second burner head using the same steps as on the first burner head.

We replaced 3 of 4 igniters on the stove top according to the previously submitted recommendations. Easy to do butt after putting one of the modules back together, we found one igniter still didn't function. We discovered the solution was to run the connecting wire under the gas tubing. Apparently it was compressed when it was over the ... Read more top of the tube and not under it.