8336 - Instructions

Went well. Changed the Ice Maker and then the Water Valve. All good and it is making ice.

I watched the video and then read the instructions. Emptied and cleaned freezer compartment. Removed old unit and removed part of old unit to be used in new installation. I then installed the new unit and turned the water back on. I let the unit produce over night and through the first batch of ice away. Because of the various regrig ... Read more erators this ice maker was used I had a little confusion recognizing our model, but worked through this problem useing some common sense. All around I'm very satisfied with the results.

I took off the front cover of the icemaker assembly and found that the gears were not meshing properly and therefore slipping. I removed the front panel and found that the white plastic cam unit under the large gear wheel had disengaged from the hole in the front plate which is why the gears were slipping. I refitted the cam and wheel a ... Read more nd it worked fine but stopped again for the same reason the next day. As the plate appeared to be buckled somehow (not user repairable) and, as the unit was leaking and pooling water (which froze) in the collection unit, I decided to change the whole icemaker.

Ordered about 1300 on a Thursday, it arrived the next day at noon and was fitted straight away. As others have mentioned, the extension cable required to fit into my old fridge made it quite cumbersome however with a bit of juggling and persuasion, I got it to fit into the cut out corner of the ice container so it is completely out of the way. Job done in about 35 minutes, making ice in an hour.

Detached the old part from the refrigerator and disconnected the low voltage quick connect. Also disconnected the water line to the Ice Maker. Reinstalled the new part in the order it was disconnected and re attached the water line feed to the valve threaded connection. Turned water on and no problems.

Seemed simple and intuitive B U T the water tube receiver fooled me. Seemed to be on backwards. So, like my wife suggested, I D I D then read the installation instructions. Yeah! It's amazing what you can do when you just RTI. :-0

Took everything apart without know what was wrong other than no ice. Worked through the parts from the water source to the ice maker. Thought it might be the water valve but ordered both the valve and the ice maker. Yeah! I have ice and in good timing with summer upon us:) Couldn't have finished it without the video, most of t ... Read more he rest was simply common sense. Single, female.

I am more than 80 yrs, always thought I could fix just about everything--but, this looked complicated. Once I received the new icemaker; took a good look where the screw-holes, etc. were, then removed the "old" one. Took about 20 or 30 minutes, then the "new" one was easily installed.

water runs in now but still does not make cubes. just keeps dripping until I shut the water off.

had to replace copper water line to valve

Instructions that came with the part were useless. I would have created new problems if I had attempted to follow the instructions. However, once I had the old part removed and put it beside the new part, required repair process was obvious, easy and quick. Frig now makes ice better than it ever did.

Followed the instructions. Smooth as silk. This part is better than the original. There appears to be a sensor that beeps when the ice reservoir is full.

Watched the video that showed how to disassemble the ice maker. Then went right in and replaced the part and turned it on. It immediately started filling up the ice tray. I still have not been able to find out why it does not make as fast as the original ice maker. The tempeature for the freezer is set pretty cold.

Ordered the part from "parts select". Removed old part, installed new part by unscrewing the old switch, simply cutting supply hose ...pluging in the new part and re-attaching water supply line. 10 minutes at most.

It was exactly as shown in your instruction video

I just followed the directions carefully, loosened the screws with a nutdriver removed the unit from the screws, unplugged the unit from the freezer plug, took out the new unit, used the adapter supplied with the unit to match up with the plug in the freezer, carefully attached the icemaking unit to the screws, carefully slid the cord beh ... Read more ind the unit, lightly clinched down the screws, checked it with a level and then did the final snug down. turned the unit on and it worked fine. Pretty easy, just take your time, don't rush and it will come out fine.