8198 - Instructions

Removed the grid. Removed the existing top to bottom wire. Restrung the grid with the new wire. Then, it cut ice just fine-better than new. Note: wire provided is only sufficient to rewire side to side or top to bottom, not both. If you need to do both, you'll need 2. Yes, lots of money for a few feet of wire.

Replaced thermal fuse

Disconnected both water lines and two mounting screws. Installed new water lines and water valve. No problems at all. Ordered the valve on a Monday and received it the next day. Even though i chose FedEx ground. GREAT SERVICE! I am a technical service manager and I always give credit to company's with great service. In fact, I have sent y ... Read more our website link to our management team to show what our website could be for our customers. Easy to find part numbers, pictures of the part being ordered and ease of use. World Class support.
Kindest regards,
Dave

Unscrewed clamp holding water tube to refrigerator ice maker. Pulled water tube from ice maker and water valve inlet. Cut the new tubing to the exact same length and inserted one end to the water valve inlet and the other end to the ice maker then screwed clamp holding water tube back to the refrigerator ice maker.

Removed back panel and removed the motor put new quick disconnect on and tapped the mounting holes. Removed and cleaned fan blade from old motor and put on the new motor. Mounted motor plugged it in and replaced panel.

Handed the parts to my son-in-law he's very mechanically inclined had the job done in 20 minutes

I followed the video instructions that were supply on your site

Removed the back panel on the refrigerator--unplugged the condenser fan motor--removed the motor--placed a small fan to cool the condenser--called parts select--ordered the motor--the motor arrived less than 24 hours after I ordered it--replaced the motor and rear panel on the refrigerator--probably saved more than $200. 00--Very happy wi ... Read more th parts select service--plus I had a misunderstanding with my credit card and john at parts select was very helpful --not their fault--excellent company

The post I read said start at the middle and work your way out towards the left and right. This was incorrect. All I did was secure one end to the torx screw and tighten it down. I then slowly pulled the wire as tight as I could around each insulator, going slow so as to not kink the wire (very easy to do). Once I was at the other tor ... Read more x screw I used a pair of linesman plyers to gently tug each wire tighter, I needed an extra pair of hands to hold the grid down. Once everything was tight I wrapped the last torx screw and tightened. Here's what no one is saying, you will not get the wire as tight as it originally was but that's ok. After I got everything reinstalled the ice maker is making ice like a champ.

order start button and was sent thermal, reordered and rep sent me a button that was not for my machine even though she had model no.,called third time and was told I had to order new control panel but they were not being manufactured any more.so it is not fixed

removed broken wire, replaced with new wire and screwed the 6 tensions screws to tighten the grid wire.

Water was not being drawn from the reservoir to the evaporator plate, so I concluded that the recirculation pump had failed. I first unplugged the machine from electrical power. To improve access to the pump, I removed the cutter grid using a nut driver and squeezing the electric connections to separate them. I also removed the reservoir, ... Read more first removing the drain pipe by pulling it downward and the using pliers to loosen the thumbscrews until I could turn them by hand. I then thoroughly cleaned both the cutter grid and the reservoir to improve performance once the repair was done. The pump is covered by a solid plastic screen attached by just one nut, which is removed easily with the nut driver. The pump itself is attached with three screws which are easily removed with the nut driver and by an electrical connection which loosens by squeezing. Indeed, Upon examination, i found that the pump shaft was stuck solid and did not turn freely, explaining why it did not work. Replacing the pump, reattaching the three screws and reattaching the electric connection was pretty easy except for the right rear screw behind the pump which was hard to reach to guide the screw without a trick up my sleeve. The trick was to wrap scotch tape around the screw and the nut driver so that I could guide the screw one-handed. Once the screw threaded through a few turns, I jerked back the nut driver, pulling the tape off the screw. I then removed the tape from the nut driver and continued to tighten that screw and the rest, and then reattached the electrical connection. I then reattached the screen, the reservoir and the cutter grid, then plugged my machine back into the electric circuit and was pleased to watch it hum back to life, good as new and performing better than it was before the pump had failed.

Followed the video on parts page. I was worried I would brake the cover but learned from the video the right way to remove the front plate. I found the video very informing. Thank you for saving me a service call and the part cost was minimal compared to a new refrigerator .

Replaced the assy. But, I would have been happier if you sold just the wires. I could have replaced the wires at a much lower cost and may have taken less than an hour to replace the wires.Still happy - the ice maker works.

1) Unplug power cable from dryer.
2) Remove the 2 screws that secure the chute for lint filter screen with
Phillips head screwdriver.
3) Remove the lint filter screen.
4) Depress plastic locking clip on each side with putty knife to release
tension and lift up top panel to clear the locking clips. Each ... Read more locking
clip is located 2-1/2 inches from the front edge of side panel.
5) Lift the top panel and lean against the wall for support. If dryer top
panel cannot be raised all the way due to cabinet(s) above, tape
the dryer top panel to cabinet above or have somebody hold the
top panel for temporary support.
6) Install the new metal locking clips. Ensure that the elongated tab
of the metal locking clip is towards the front of dryer. Compress
locking clip lightly with pliers and push down into the hole.
7) Lower the dryer top panel and press it down in place over the metal
locking clips for a tight fit.
8) Reinstall the 2 screws to secure the lint filter chute.
9) Reinstall lint filter screen.
10) Reconnect power cable for dryer.
11) Turn on dryer and inspect that all dryer panels (top, sides and
front) are tight and secured.
Repair Duration: 5 minutes