8159 - Instructions

Replaced idle pulley wheel, worn drum belt and all 4 rollers (1 frozen) due to dryer age. Site video re general disassembly/re-assembly easily adapted to this model and very helpful with exception of replacement of drum rollers. New rollers received (AGM75510755) were pre-mounted on included shafts. This required removal of existing roll ... Read more er shafts to replace with new shaft/roller units. Site video shows placing a new roller on existing shafts after removing a plastic retaining clip. New roller/shaft assembly is a better option and fortunately I did not order extra retainer clips! Rear drum roller shafts have small carved out space to fit a box end wrench to remove shaft nut. Watch out for sharp edges on internal steel parts!

Following the reference video, step by step and taking progress photos along the way, organizing screws and hardware as they were removed.

The discrepancy I found was the new rollers that I received were complete with the shaft. The video with the older rollers instruct removing the rollers from the shaft.

To use th ... Read more e new rollers with the new shaft, requires removing an additional panel at both the front 2 and also the full back panel for the rear 2, to get a wrench on both ends of the shaft, and then attach the new roller bearing shaft assembly and re-install the panel.

Other than that, it went very smoothly and the result was a quiet rotating drum. No more thumping!

My dryer actually required 2 moisture sensors, but had only ordered one pack, which only came with 1 sensor. For whatever reason, I thought the pack would have had the 2 pieces.

Another reviewer made note to wear work gloves as some of the hardwares metal edges are quite sharp. Following that advice I completed the repair in 3 hours without a scratch. Thanks for the detailed video Partselect team and good luck to all attempting repairs.

Completly disassembled dryer removed 2 rear rollers installed 2 new rollers. Reassemble dryer in including new drum belt. Dryer is nice and quiet again running fantastic, thank you for your support

I'm not for reading instructions. So I just dove right in and took the dryer apart to get down to the motor. I gave the dryer a thorough cleaning and replaced the 3 parts I ordered from the online recommendation. Wish I would have ordered 2 sensors and the 2 thermostats that are near the burner. Just so replace beings I was in there. Repl ... Read more acing the parts was easy, found them just by looking for matches to the new parts. Reassembled the dryer, dont think I put a single screw back where I got it lol. And still haven't put the top lid back on due to difficulty. Not sure if I even needed any parts, found a nest in my outside vent completely plugging it. But after a good cleaning and replacing the parts the dryer dries the best it has since we've owned it. The dryer came with our house which we bought 3 years ago and it was 2 years old when we purchased the house, so it is now 5 years old.

First do not watch the videos . They had you taking the insides all apart
when all you had to do is pull the unit out , twist the motor out and put the new one back in. Take nothing apart inside the dishwasher.

Removed top of dryer
I carefully removed wires from back of control panel
Removed control panel
Most of screws hold cabinet together
Unhook wire from light on door and sensor on the front panel.
Remove the front door and panel together
I changed both front rollers on front panel
If you have to change r ... Read more ear rollers lift tub up by belt
Remove screws on back of dryer that will let you lift out inside rear panel that holds the rear rollers
Change rollers and just revearse procedure to put back together

Like another post, the start relay rattled like a baby rattle. Replaced the start relay and freezer works great.

i looked byhind the freezer , the mottor has the relay connected to it.i took out the relay, and i descovery something was loose inside, i decided to take to check out at sears to see if they have in stock that especific relay. they did not have, they could order, that's when i dicided to go ahead and looking for in the internet, good i f ... Read more ound PARTSELECT,they had the part and i was very nice attended,they sent in 2 days i had fix my freezer. thanks PARTSELECT. gilmar couto.

The site offers a video for this part which worked perfectly. In addition to replacing the part, since the cardboard panel was off, we also cleaned all the dust off of the coils which someone recommended to do annually.

Handed the parts to my son-in-law he's very mechanically inclined had the job done in 20 minutes

I followed the video instructions that were supply on your site

I took the dryer apart. You have to take the top off, then the door/front off. There are wires & other parts that need to be unhooked as well. A flat tip screw driver can be used to pop the top off. The screws were all phillips. Once you take that all apart, then you can access the drum. I bought the belt because I thought that was what w ... Read more as wrong with it. Turned out to be hair in the drum rollers. Took those all off & put wheel grease on each of them, put new belt on (since I had it LOL) then put it all back together. Make sure everything is lined up correctly otherwise you will have to take it apart & reline (which I had to do)
I am a 49yr old female & was able to do this repair on my own!

The replacement of the light no problem, the reason the light broke; problem. The original was glued in (for transport i think) and simply trying to unscrew it out (in a very tight slot) it broke; be careful or you’ll be buying a new $20 bulb (with shipping and handling).

Un screwed the cover but when i tried to remove the bulb it was broken at the base. I disconnected the power and used neddle nosed pliers to remove the base

I unwired the overload and installed the new overoad. Plugged the starter in to the back of the compressor and wired it up. Now I'm trying to get the freezer filled up again!