8139 - Instructions

An appliance repairman determined the problem which was that it needed new pulleys and thankfully PartSelect carried them. He installed them in an hour and my dryer runs fine now.

Pull filter out and replaced with new one.

FIRST REMOVED THE LID ON TOP OF DRYER.THEN THE CONTROL PANEL AND THE STEAM TRAY. HAVE TO UNCLIP TWO HARNEST CONNECTORS. REMOVED THE FACE PLATE THAT HOLDS THE DRYER WALLS TOGETHER ALSO REMOVE TO SENSOR HARNESS CLIPS. .REMOVED THE BELT FROM MOTOR. TOOK DRUM OUT . UNCLIPPED MOTOR COLLAR SNAP CLIPS DISCONNECT THE MOTOR HARNESS. INSTALL NE MOT ... Read more OR AND CONNECT HARNESS INSTALL CLIP . REINSTALL DRUM AND PUT BELT ON. CONNECT HANESSES AND INSTALL FACE PLATE. INSTALL CONTROL PANEL AND THE TOP LID.

Watched a repair video. Very easy to replace, about an hour to repair.

I watched a YouTube video with how to take the dryer apart and remove the sensors. I followed the what the instructions were removing the top of the dryer and then the front panel. Once that was removed it was a matter of removing 7 more screws and the lint collector piece came off. Popped the sensor pieces out. Cleaned the inside of the ... Read more dryer and reinstalled a total of 5 parts and dryer is working fine and the clothes are drying in the allotted time it use to take.

Followed video provided on site

My cleaning lady brought her handy husband over Saturday to help me. The only tool we used was a Phillips-head screwdriver. I went online earlier in the week and found a good video put out by Repair Clinic and another one I found on You-tube on how to disassemble the dryer. After watching several times, I knew I could do it. We worke ... Read more d together, I cut my hand on the inside edge of the control panel, but, when I hit a snag, we watched that part of the video again and worked right through. Replaced the Thermistor, NTC first, not a problem. Then the Heater Assembly, not too difficult. I couldn't find where one of the remaining parts went, so, we reassembled the dryer and gave it a try. Worked like a charm. We did remove a lot of lint from inside the cabinet and around the felt liner on either end of the drum. It works like it did when it was brand new. Highly recommend to work with someone, so, you don't get frustrated. I am 65 years old and this was a no brainer for me, although I am somewhat mechanically inclined. Very empowering to accomplish this repair. Just follow the video.

thank you for the video--very clear, responsible, applicable although the illustration was not exactly of our kind of light. the bulb was exactly like the one Hotpoint used in its microwave made in 1989! I will come back to you for parts in the future. (You have the model # from my original order.)

A little research told me the hum plus no cooling was either the compressor or the relay. I ordered the new relay and put it in but it didn't fix the problem. I ended up having to buy a new fridge, but it was worth the $30 gamble to see if I could fix it on the cheap and it saved me the money a service call would've cost. Pretty easy i ... Read more nstallation, just in a tight space on my model.

After trying duct tape to fix the tear, I decided to see if I could just order a new one. Part Select was the first company I found listed, so I ordered one. It was not expensive and it was delivered very quickly! It works so well s as me I’m a very happy customer!

Last week I removed the glass cover that was held in by one screw and removed the burnt out light bulb. I ordered the bulb and left the glass cover off until the bulb arrived. I had to wait until this evening to put the glass cover back on and fasten the screw because I have a window right next to the oven and the sun streaming in made ... Read more it too difficult for me to see how to put the glass back in and replace the screw.

Slide out old filter then slide in the new one.

Slide out the old lint catcher, and slid in the new one, not that hard.

I did as I was told (by my wife). Bought the machine from Home Depot - no side vent kit - had them complete the installation today when the kit came.

Removed old lint filter inserted a new one.