8032 Snapper - Parts

This is a genuine OEM sourced component used on many Snapper lawn mowers. The metal hex shaft is fitted onto to the mower wheels, and powered by the pulley in the drive system. The hex shaft is sold individually. A wrench, pliers and a screwdriver are often helpful for the removal and replacement.

The pushnut retainer goes next to the ball bearing. This is available as an individual replacement part. This item is an OEM from Snapper, Murray, and Simplicity for use in lawn mowers, lawn tractors, and snowblowers. It might require a wrench to replace this part. It is made of metal and will need to be replaced if it breaks.

This is an authentic replacement part manufactured for use with rear engine mowers and lawn tractors from Craftsman. The user will need to replace this hex nut if it is missing or not working correctly. This hex nut screws onto the transmission link lever. This part is made of durable material and sold individually.

This is an authentic manufacturer-sourced replacement part which is designed for use with Snapper lawn mowers. It is the special seal for the long axle assembly, please make sure to check appropriate diagrams of your model for correct location and use of this hardware. Over time seals tend to get compressed and may crack eventually requir...Read moreing replacement to maintain peak performance. It is a high-quality component which is made of durable rubber material and it is sold individually.

This gas tank cap is an OEM replacement part supplied by Snapper. It is compatible with over 150 models of rear engine riders. This cap provides a cover for the gas tank in the machine. It is designed to prevent the tank from leaking gasoline. This part is made of plastic and sold individually. No tools are needed to replace this part.

This hex center lock nut is sourced from the original manufacturer for use in lawn and garden power equipment. It is a hexagon-shaped fastener for bolts/studs that is responsible for the keeping the bolt/studs secure during use. The nut is made of metal and has a diameter of 5/16 of an inch and a thread pitch of 18 internal threads per in...Read morech. Over time the threads in the nut can wear down and the nut itself may crack or break. It is important to replace it as soon as necessary to avoid damaging your equipment. Use a socket or wrench to remove the old nut and thread the new one on. Make sure to order the correct number of nuts for your equipment as each nut is sold individually.

This is a genuine Craftsman replacement part that is sourced from the original manufacturer to be used with snowthrowers. The metal hex nut is commonly used to fasten the bolt that secures the height skid to the auger housing. This item is available as an individual replacement part, please note four nuts may be required.

This is a genuine Murray and Snapper part sourced directly from the manufacturer for use in lawn mowers. The right hand lower handle is made out of durable materials. When replacing this item a socket set and a wrench set might be required during the installation process. It will need to be replaced if it breaks. This part is available individually.

This is an original replacement part sourced directly from the manufacturer. The retaining ring is commonly found in riding mowers from Snapper and Murray. This part is made of metal, and is generally used to secure the bearing in the spindle housing. Please be aware that there are different retaining rings used in the machine. Refer ...Read moreto the parts diagram to be sure of ordering the correct part. You may require pliers when replacing this item. The retaining ring is sold as an individual replacement part.

This is a genuine item that is supplied by the original equipment manufacturer for use with Murray and Snapper lawn and garden equipment. It is an identical replacement for a missing or a faulty lever that was installed on a new unit, please make sure to refer to the appropriate diagram of your model for the correct location and applicati...Read moreon of this component. This high-quality item is made of durable plastic and is sold individually, keep in mind the hardware to secure it is sold separately.

The wing-nut is made out of metal and attaches to various other parts. It is a genuine OEM sourced part which is specially designed for use with lawn tractors made by Snapper and Simplicity. This part is available as an individual replacement even though several may be needed. It will need to be replaced if it becomes broken or stripped.

It is an authentic OEM item that is designed for use with a variety of lawn and garden equipment. A washer is a special part which helps to provide a tight fit between connected components. This part provides an identical replacement for a damaged or a missing hardware that was installed on a new unit. It is a standard hardware which may ...Read morehave multiple applications. Make sure to check the appropriate diagrams for your specific model for the exact location and the correct application of this cone washer. Note, it is made of durable metal and is sold individually.