EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

8003 - Instructions

All Instructions for the 8003
16 - 30 of 48

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
UNABLE TO INSTALL DUE TO DAMAGED IN SHIPPING
3 of 4 people found this instruction helpful.
  • Tina from EL DORADO, KS
  • Very Difficult
  • More than 2 hours
WORTHLESS...I EMAILED YOU ON 2/7/22 AFTER RECEIVING THE DAMAGED FILTER DUE TO NOT SHIPPING IN A HARD OR SOMETHING IN THE ENVELOPE TO PROTECT THE FILTER FROM BEING BENT.
I HAVE NOT HAD ANY RESPONSE FROM YOU FOR THE DAMAGED FILTER OR WHEN I CAN EXPECT ONE THAT I CAN USE.
UNSATISIFACTORY SERVICE!
Was this helpful?
Thank you for voting!
Replacing top vent filter
2 of 3 people found this instruction helpful.
  • Paul from CHARLOTTESVLE, VA
  • Very Easy
  • 15 - 30 mins
  • Screw drivers
Followed owners manual instructions to the letter: removed two top screws, opened the unit door so I could slide out the old filter. We don’t cook much at all in the unit, mostly just heating coffee and reheating leftovers. BUT! The top grill was pretty greasy and needed hot soapy water to clean, including in the depths of the top area. T he whole process, especially the company website for part ID and purchase, was slick!
Was this helpful?
Thank you for voting!
Replace resin cover in microwave
1 person found this instruction helpful.
  • Paul from MCMINNVILLE, OR
  • Very Easy
  • Less than 15 mins
Used fingers to pull damaged cover away from microwave interior body. Used fingers to snap replacement cover into open slots.

Cover snap right into special slots.
Was this helpful?
Thank you for voting!
microwave air vent fell out
1 person found this instruction helpful.
  • Chris from ROFF, OK
  • Very Easy
  • Less than 15 mins
  • Screw drivers
the vent broke enough fittings that it couldn't be fixed, Needed replacement. Even with a slight part number, Part Select had the proper part thought description. Be prepared for a fixed screw support, Didn't see that until installation. Worked as advertised.
Was this helpful?
Thank you for voting!
The new part was too thick for the worn out plastic ring which is obsolete.
1 person found this instruction helpful.
  • James from PURCELLVILLE, VA
  • A Bit Difficult
  • 30 - 60 mins
Needed to raise the part to match the ring. I used peanut butter to hold plastic shim while replacing to hold it in place. Built in Oct. 2009.
Was this helpful?
Thank you for voting!
Microwave fan would come on when door open. Timer and unit would not switch on.
1 person found this instruction helpful.
  • Dick from SANDY, UT
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
I looked up my problem on the internet and found a very helpful video. Microwave on video was different brand but the internals and methods were very much the same. The video made it simple and easy to fix. Found the replacement switch on the LG parts site and ordered. Two different switch types. One with red switch, the other green. Part was $7.28. Saved a bundle in service costs. Here is the repair video.

https://www.youtube.com/watch?reload=9&v=_AglBJoHgDs
Was this helpful?
Thank you for voting!
turntable wobbled
1 person found this instruction helpful.
  • James from Rantoul, IL
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
removed power cord replace turntable motor by lowering bottom panel removing two screws holding the motor on and two wires and reinstalled
Was this helpful?
Thank you for voting!
Wanted to see the instructions before I install it.
2 of 5 people found this instruction helpful.
  • Rene from MORENO VALLEY, CA
  • Really Easy
  • 30 - 60 mins
Wanted to see the instructions before I install it.
Was this helpful?
Thank you for voting!
Door Latch spring keeper broke
3 of 8 people found this instruction helpful.
  • Gregg J. from WEST CHESTER, PA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Removed door from microwave and then popped the inside widow trim ring off. Removed 4 screws from the window bracket, replaced the latch with a new part and then assembled.
Was this helpful?
Thank you for voting!
Microwave operated but did not heat
3 of 10 people found this instruction helpful.
  • Donald from Oak Ridge, TN
  • Easy
  • 1- 2 hours
  • Screw drivers
Initial failure of over range microwave Aug 3rd. Control Panel worked but no heat. Took to local LG authoriaed local repair place. They fixed it quickly and we re-installed it. Worked fine for 2 months then had similar failure again. Agaim took to same authorized repairer. They kept unit for 3 months but finally concluded theu could not fix it and suggested we contact LG for a partial refund. When they tested the unit during re-assembly in my presence, there was a blue flash and the fuse blew. Since we had built a custom tile mural back splash around this unit, I brought it home, ordered a number of time delay fuses new capacitor and two new high voltage diodes. However, using my Fluke DMM, I checked the existing capacitor and high voltage diode and they checked OK so I just replaced the time delay fuse. The high voltage transformer leads had 2 possible ways to connect to capacitor and diode. Tried one way, plugged unit in and turned it on, and immediatly blew the fuse. Replaced the fuse and reversed the high voltage transformer connections,amd turned unit pn, and it worked perfectly. Since we had experienced several power failures during the time of the original failure, the repairer concluded that power spikes might be at fault, so I also purchased a TrippLite ISOBAR4ULTRA 3300 Joule surge protector between wall outlet and microwave, and re-installed over range. It has worked perfectly since.
Was this helpful?
Thank you for voting!
Shaft socket was worn out
0 of 1 people found this instruction helpful.
  • Cesar from Miami, FL
  • Really Easy
  • Less than 15 mins
Pop old one out and replaced it with new one.
Was this helpful?
Thank you for voting!
light bulb replacement
9 of 29 people found this instruction helpful.
  • Marianne from CHURCH HILL, MD
  • Very Easy
  • Less than 15 mins
very simple
Was this helpful?
Thank you for voting!
Headlight stopped working
1 of 6 people found this instruction helpful.
  • Darrell from RICHMOND, VA
  • Very Easy
  • Less than 15 mins
I tried to order a light socket but you sent me a blade then cancelled my order and refunded my money after I waited for the right part.
Was this helpful?
Thank you for voting!
Mixer began to make a noise on speed two and higher
8 of 31 people found this instruction helpful.
  • LISA M from BATESVILLE, AR
  • Really Easy
  • Less than 15 mins
We took our 30 plus year mixer apart. I removed the old grease. There was some crumbly looking grease in the main housing gear section where the nylon gear is located. It looked like it had flour mixed in it. Not certain. Removed as best possible all old grease and applied 6 oz. of new Benalene grease to all of the gears. Now it do es not make the slight howl sound.
Was this helpful?
Thank you for voting!
Broken Tray ,Glass
  • Gena from ROSICLARE, IL
  • Really Easy
  • Less than 15 mins
Received my replacement Tray,Glass in only 2 days. Opened it and placed it in the Microwave. Yep, it was that easy!
Was this helpful?
Thank you for voting!
All Instructions for the 8003
16 - 30 of 48