8002 - Instructions

I decided the door switch was the problem because 2 problems happened at the same time. I removed the 4 screws for the top outside cover and the 1 screw that held the control board. After removing the control board screw, I lifted it up and removed it. This gave me access to the 3 door switches. I then removed the 2 screws that held t ... Read more he plastic piece that holds the switches. This made it easier then to replace the switches.

I didn't. Don't know how to get to light bulb to change it for this specific model

Not knowing which of the switches to replace I ordered all three in the assembly. Replacing the full assembly was easy, first unplug the microwave. Then remove the top cover to access the screws that hold the control panel in place and let the control panel hang. There are two screws that hold the assembly in place - remove those. I u ... Read more sed needle nose pliers to pull the wires off of the switches and immediately put the wires on to the new assembly so there was no confusion on what wire went where. Place the assembly back in position, replace the two screws to hold it in, put control panel in place and secure screws. Replace top cover and plug in.

I removed the bottom plate which had 9 screws.
than unplug 2 wires to the motor and unscrewed 2 screws, replaced the old motor with the new one and also the coupler. and so far no noise. easy fix. Thanks

Entered dryer from rear exhaust port. Removed 2 screws and 2 clip on wires. A little awkward of process but superior method over disassembly of drum and main parts.

Followed YouTube video repair process. The only problem is that the door hinge has plastic bushings attached. A couple broke and the parts listing does not show the bushings, nor does the hinge come with them. The door is a bit loose without them. Nonetheless, the repair did the job for now.

One of the roller assembly froze up & had a flat spot on it. There for causing the drum not to rotate. Pulled it out replaced the roller & up & running.

Unplugged the microwave. I opened the door. I used a butter knife to pop the bezel off the inside of the door. I pushed the locker up and to the left and used the butter knife to pry it loose. Disconnected the locker from the spring, and reversed for the installation.

This is a piece of cake. No tools are actually needed. Grasp one end of the old seal and gently pull it out of the groove in which is fits. Take the new seal, and paying attention to which way around it fits (there is a right and wrong way!) start at either end. Leave an inch or so beyond the groove to rest on the bottom of the dishwa ... Read more sher, and press the seal in place in the groove. You should have an inch or so left at the far end. Go back and go all along the seal and make sure it is pressed evenly and completely into the groove the full length.

You're done.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I did a continuity test and determined the old element was bad - ordered the new one and put back the screws. All done!

Removed the MW from the wall. Took the top screws off the air vent. Then removed the two screws holding on the display. I then moved the display to its side and it revealed the micro switches. I removed the plug in leads from the micro switch one at a time. I did this with all three micro switches only one at a time. I reinstalled everyth ... Read more ing and plugged it in. No more fans starting when the door is opened.

Read the troubleshooting section on this site. Figured it was an interlock problem because the food was not getting hot (magentron not turning on) and the carousel was not turning. Did not think both the carousel motor and magnetron failed at same time, thus indicated an interlock problem. The interlock switches are actuated by the door ... Read more latch. Replaced the assembly locker piece with all three switches (only a $20 dollar part) and microwave was fully operational again. Wife and kids think I am a hero.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I had to use a mirror and flashlights to see in the back of the oven to replace the screws in the new element. It was very close quarters and difficult to see behind element plate.

Removed the top, the control panel and the door. The heater assembly came out thru the front, without having to remove the drum. Easy replacement

I ordered the wrong part....needed their help to locate the correct part.
Sent 3 emails asking for help to the 'customer service' email ----NEVER heard a word!!!......and now they want me to rate the installation ?!
Horrible customer service