All Installation Instructions for Kenmore Refrigerator 795723

Spring in the plate front assembly broke. Door plate assembly would not move into correct position, preventing door from closing.

1 person found this instruction helpful.

Robert from WARREN, RI
Very Easy
Less than 15 mins
Screw drivers

Followed Youtube video provided on the PartsSelect Website:

https://www.partselect.com/PS12374439-LG-AGU75188619-PLATE-ASSEMBLY-FRONT.htm?Inventory=12374439&SourceCode=20&SearchTerm=LFX28979ST

Made installation of the new part a piece of cake. Easy peasy!! Took less than 10 minutes.

Was this helpful?

The switch became intermittent - Possibly a poor designe

1 person found this instruction helpful.

Sidney from ENDICOTT, NY
Very Easy
Less than 15 mins
Screw drivers

Used a small screw driver inserted into the front of the switch (facing the front) and pried until the switch was coming out. When out, I removed the connect harness and replace the switch with a new one.

Was this helpful?

The door bin cracked and broke.

1 person found this instruction helpful.

Elizabeth from Huntington Beach, CA
Very Easy
Less than 15 mins

I just popped out the broken bin and slid the new one into the slots on the door.

The fix was easy. I appreciate the expert advice on which part to purchase, as that was difficult to figure out. I received a prompt response to my question and the replacement part came quickly.

Was this helpful?

Replaced cracked refrigerator door shelvers

1 person found this instruction helpful.

Larry from SANTA ROSA, CA
Very Easy
Less than 15 mins

Slid the replacement shelves into place.

Was this helpful?

Door light switch, 3rd one I have replaced in 6 years made in China.

1 person found this instruction helpful.

Charles from CURWENSVILLE, PA
Really Easy
Less than 15 mins
Pliers, Screw drivers

Easy install, small screwdriver under back of old switch push out and pull out with small pliers. unsnap the old plug and install new. YOUR DONE

Was this helpful?

Old part did not seal properly

1 person found this instruction helpful.

Donald from MERRITT IS, FL
Really Easy
Less than 15 mins
Screw drivers

Read the reviews from other members and just did as they said. Needed a screw driver and the info from past persons review couldn’t have been easier.

Was this helpful?

Removed old part.

1 person found this instruction helpful.

Steve from NORTH AURORA, IL
Very Easy
Less than 15 mins
Screw drivers

Installed new one.

Was this helpful?

Freezer door gasket needed replacing.

1 person found this instruction helpful.

Stephen from DICKINSON, TX
Really Easy
Less than 15 mins
Pliers

Simply removed old gasket. Started in a corner with installing the new gasket. It went in easily and quickly.

Was this helpful?

The spring on the mullion was broken so the mullion would not open to seal the other door.

1 person found this instruction helpful.

JANET from GRAND JCT, CO
Very Easy
Less than 15 mins
Screw drivers

I am a73 year old woman. If I can do this, anyone can. Super easy. Just watch the online video.

Was this helpful?

door slight switch failed

1 person found this instruction helpful.

Greg from CASA GRANDE, AZ
Really Easy
Less than 15 mins
Pliers

Covered the sidewall with tape to protect. Pried the switch out with knife blade and removed electric plug with needle nose pliers. placed plug in new switch and pushed switch into the hole in the side wall. Took about five minutes.

Was this helpful?

Spring broken in door mullion

1 person found this instruction helpful.

Wayde from SEMINOLE, FL
Really Easy
Less than 15 mins
Screw drivers

Took 2 screws out and disconnect wire and install new part.

Was this helpful?

Replace switch

1 person found this instruction helpful.

Dean from HILLSDALE, MI
Really Easy
Less than 15 mins
Screw drivers

Read previous tips
Taped off area around switch to protect surface
Used putty knife to extract switch
Used screwdriver to separate connector from switch
Plugged in connector
Pushed switch assembly into opening
Removed tape

Was this helpful?

roller was missing in freezer upper drawer

1 person found this instruction helpful.

Bob from LIBERTY TWP, OH
Really Easy
Less than 15 mins

easy, just lift the drawer and insert the roller assy.

Was this helpful?

The hose that feeds the Ice Maker broke,right where it goes in the Fridge.

2 of 4 people found this instruction helpful.

William from BOWDOINHAM, ME
Easy
1- 2 hours
Screw drivers, Socket set

I actually didn't use what I got. Because there was all kinds of tubing coiled up in the door. We just fed the exsess all the way through the Fridge,and Bingo! It was done.

Other Parts Used:

Filter Assembly

Refrigerator Water Filter LT700P

Was this helpful?

The Ice maker stopped working

2 of 4 people found this instruction helpful.

Joseph from SAINT LOUIS, MO
Really Easy
30 - 60 mins
Pliers, Screw drivers

Thanks to videos on You-Tube which showed step by step removal and replacement. It was a simple process. only thing missing on the video was information on the green ground wire.

Was this helpful?

795723 Kenmore Refrigerator - Instructions