EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

79096313402 Kenmore Range - Instructions

All Instructions for the 79096313402
76 - 90 of 117

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Needed to install an anti-tip bracket on my stove.
  • Daniel from Provo, UT
  • Really Easy
  • Less than 15 mins
  • Socket set
Moved the stove. Used the template to position the bracket. Put the supplied screws to attach bracket to the floor. Slid stove back into place. DONE!
Was this helpful?
Thank you for voting!
Purchased home where previous owner melted Aluminum Foil to bottom panel of oven.
  • Michael from Wimauma, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed 2 screws from rear of panel and dropped new panel in. Re-installed screws. Oven like new again. Aluminum foil was burning and emitting foul odor when oven was on.
Was this helpful?
Thank you for voting!
shorted out small element burner switch
  • Alvie from Walnut Cove, NC
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
First, I disconnected the electrical power by pulling apart the plug behind the range. Next, I removed the screws holding the service plate on back of the top panel.I removed the switch knob by gently pulling it from the stem. Underneath I found 2 screws holding the switch in the panel. I removed these with a phillips screwdriver.I was ab le to pull the entire switch out to the rear leaving all wires attached.The new switch looked different from the original and the wires were configured differently but the wires were clearly marked. By removing one at a time and placing it on the new switch to the corresponding marking,it was a simple matter to wire the switch.I reinstalled the switch in the panel,put back in the screws to hold the switch, slid the knob back on the stem, reinstalled the rear panel,and plugged the power cord back in.The switch worked perfectly.
Was this helpful?
Thank you for voting!
oven was too hot code f-10 came up
  • Donnie from McLaughlin, SD
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Pulled out range, unplugged power used nut driver to remove back and removed oven probe. Had to change end and reinstalled in reverse order.
Was this helpful?
Thank you for voting!
The warning light for the warmer was stuck "on"
  • Linda from Pleasant Mount, PA
  • A Bit Difficult
  • 15 - 30 mins
Turned off electric at the main box. Removed glass top. Used a razor knife to pry the connections loose so that the new connections could be slid in. Problem was that the element ordered looked entirely different then the original one. Even the hookup was different. But once the connections were made, the ceramic top placed on top, and th e electric restored everything seemed okay. The warmer works and when it heats up the warning light turns on. When the warmer cools the warning light goes off as it should.
Was this helpful?
Thank you for voting!
burner wouldn't heat up
  • Stephen from Columbia, SC
  • Easy
  • 15 - 30 mins
  • Nutdriver
I unplugged the stove. Then I lifted up the top of the stove to expose the burners. I unscrewed the necessary screws and plugs that attached the old burner to the stove. Then I simply put the new one back in it's place. The stove was one of those flat burner stoves, and I was a little concerned that I would be able to do it. The repair m an wanted to charge me $150.00 for labor.
Was this helpful?
Thank you for voting!
No current to the burner
  • terry from Pensacola, FL
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Checked the burner and no power to heat the burner. removed the old switch and put on the new one.
Was this helpful?
Thank you for voting!
Sensor probe was not sebding proper temp to themostat which regulate the 2 heating elements.
  • Grayson Crisis enter from Sherman, TX
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
This is a slide in oven fully contained not in a wall, or wood enclosure. I slid the unit out away from the wall unplugged the power cord, used the nut driver to remove a dozen screws, not all of them, you dont need to pull the top back plate off just unscrew the bottom 3-4 screws on the top plate to release the lower back cover plate and you see the probe wire and the insertion point/hole. I actually did not even need to pull the full back plate off but it makes the handling of all the tools and stripping easier. I wish they had just left the plug off of the new probe and had left the 2 loose ends of the 2 wires that had to be spliced, it would have saved 15 minutes just with that part. If you dont have a real splicer tool ya gotta be careful to not cut the wires themselves if you use a sharp knife. Just cut the new probe plug off and splice on the old plug from the bad sensor which obviously you have cut and strip as well as I did and then it fits nicely back together like it was ment to be. I put elect tape on the 2 splices, you could use small wire nuts or whatever you desire, but turn the exposed splices back away from each other and tape them to the insulated wire so no exposed wire is touching any metal then I wrapped the completed taped splices with about a 4x5 piece of aluminum foil to help deflect the residual heat coming from the oven when it is on. put the probe through the hole and placed the metal retainer back in place and re- mounted the back panel plate,cover, that was it problem solved. This entire problem was caused originally in this relatively new oven because people who have been using the oven were sitting heavy pots and pans on the oven door and the hinges were sprung. The door would not stay shut during cooking. I dont know how long this had been going on before I discovered the issue. Once I replaced the hinges ( parts select ) the uneven, wrong temp, extended cooking problem jumped up. I am certain it was related to the open door not shutting for several months. They were using a bungie cord to pull the door closed and not completely. At this point I feel very comfortable with using parts select for all my appliance parts and advice. The folks here at my facility think I am an Einstien but when you have parts select working with you in the background you can't go wrong. I asked a hundred questions and learned alot and saved the facility at least 400 dollars by doing it myself. Thanks to my new work buddy PARTS SELECT. I was really a bit apprehensive about the doors hinges they looked dangerous and might have been but the tech I spoke with at P.S. walked me through it on the phone and I read the blogs which are really helpfull SORRY THIS ONE IS SO LONG.
Was this helpful?
Thank you for voting!
inner glass door was broken
  • Norma J from Riverview, FL
  • Difficult
  • 30 - 60 mins
removed the door from the range. removed the 4 layers of glass and carefully set aside the unbroken ones. the 3rd and 4th glasses were held together with a metal frame which had to be dismantled. The old broken glass was rusted and hard to get out of the frame. It had to be cleaned thoroughly of broken glass and rust. the removal process could then be reversed to assemble the parts and re assemble the door to the front of the range
Was this helpful?
Thank you for voting!
inner oven door glass broken
  • Cheryl from Derby, NY
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
I was unable to loosen the screws myself so I called my friends husband to help me. We watched the video together and followed the instructions. The door in the video was a bit different than mine but this repair was easy.
Was this helpful?
Thank you for voting!
broken inner glass
  • Neal from Warsaw, IN
  • Easy
  • 30 - 60 mins
  • Screw drivers
Removed oven door. Removed screws from bottom of door as well as handle screws. Remove inner panel to expose glass. Replaced glass panel and reverse steps. Very easy.
Was this helpful?
Thank you for voting!
Broken oven door glass
  • Joseph from Cranberry township, PA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
I followed directions for replacement of the glass from the web. Replacement was simple and easy.
Was this helpful?
Thank you for voting!
burner would not heat up
  • MARGARET from MILFORD, PA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
simple, removed a few screw's, unplugged old burner, plugged in the new one. that was basically it. easy!
Was this helpful?
Thank you for voting!
Door glass cracked
  • Mike from Collegeville, PA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Really straightforward - just took door off of the hinges and worked taking it apart until I got to the front glass that was cracked. Took it out and put the new piece in and reversed the process. Really easy and I got to clean each piece on the way back in to get rid of some spills.
Was this helpful?
Thank you for voting!
Cracked inner oven door
  • Steve from Hollypond, AL
  • Easy
  • More than 2 hours
  • Pliers, Screw drivers
Removed outer glass first ,then worked my way thru to inner glass..
Was this helpful?
Thank you for voting!
All Instructions for the 79096313402
76 - 90 of 117