79092204013 Kenmore Range - Instructions

Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.

I followed two very good videos on how to do the repairs. It took longer to clean all the disassembled parts and the glass than it did to actually do the repair.
A word of caution: Be sure to lock the door hinges in the open position before you lift out the door. They must be locked open to put the door back on. It's difficult to loc ... Read more k them open once the door is removed. Also when you replace the screws get them all aligned in the holes before you lock everything down.
The infinite burner switch was pretty easy to replace but watch out for sheet metal cuts when you are removing the back of the stove. I recommend gloves. My stove has a 12 inch infinite burner, but the parts list only mentions a 10 inch burner. Before I ordered it, I had to call the company to verify that it could be used for the 12 inch burner as well.

I actually watched Youtube while I was changing it. This video was not actually the same make up of my oven, even though the I typed in the model number. I manage to figure it any with the steps anyway. It was harder then I expected but not horrible. I think I did pretty well for a women. Patti

Easy as 1-2-3

Ensured breaker was off. My range is hot wired. Removed all cables from old terminal block with nutdriver. Used phillips head screw driver to remove old terminal block from back of range. replaced old terminal block with new one. Re-attached accessory cables to small terminals first, then the main cables to the terminal block using where ... Read more necessary long nose pliers. It is important to make note of which cables are attached to each terminal of the block, so make a sketch PRIOR to removal. Also be careful how the cables are attached to the block. You are using 10 gauge cable with thick insulation. It is important that when pushing the range back into position the cable does not put too much pressure on the block as it will break it. That's exactly what happened to this last one. It probably cracked under the strain of the pressure of the cable and finally current running through it weakened it to the point where it broke off from the block causing it to short and trip the breaker.

Confirm the problem and check electrical diagram to see if there was any other circuit in the syatem that could cause the burner to stay on , remove back cover and inspect switch contacts, found them burnt , look up parts for the model number and replace it.

A Phillips screwdriver and pliers were all the tools required. At first glance, the physical appearances of the OEM and the replacement were not identical. The slide-on electrical tabs were numbered on each in the same way. Sliding off the connectors and re=connecting them on the same number tab on the new switch was all there was to i ... Read more t.

The video was a great help. I could have replaced the switch without watching it, but it gave me confidence that I was doing it right. Everything went just like he said it would. Burner seems to work better now and no more scary noises.

Took door apart, went online to partselect, ordered new glass, and put it back together. Oven looks like new. Makes sense to order the isolation as well when you do the repair

removed six nutdriver screws and removed rear cover. the only problem i had was the new switch they sent was a little larger then the orig.had to figure out the wires. fit good and works perfect.

To find problem. I turn the power off to range. Removed top back panel. Removed switch and found there was a black spot on white covering of switch. So I order a switch. When it came I turn power off to range. Removed the top panel on back of range. Removed one wire at a time and put it on the new switch. Once all wires were on new switch ... Read more . I removed old switch and installed new one. I then reinstalled the top back panel and turned the power back on. It is really easy to do. If you are not confident enough. Take a picture of the back of range before removing the panel. Then take a picture of the wires before you remove them.

Screwed up by not shutting breaker. Shorted out 3 switches. Thought i could get away without shutting breaker that was a costly error. No problem replacing the 3 switches and element switch. Took about 1/2 an hour.Always shut breaker before doing any electrical repairs.

watched the veido first then un pluged the stove then i took out 6 screws and 2 from the switch and reversed every thing

Took back cover off 2 screws held the switch then moved wires one at a time from old switch to the new one put everything back plugged in stove everything worked

simple, removed a few screw's, unplugged old burner, plugged in the new one. that was basically it. easy!