This fuse, also known as a cartridge fuse, is a genuine OEM replacement part for microwaves. It has a glass cylindrical body with a metal cap on each end. The cap connects the fuse to the circuit. If the current goes above the fuse rating, the element inside the glass will melt and cut off the electrical current to the appliance. This pro...Read moretects the circuit and surrounding components from overheating and becoming damaged. Once the fuse is blown, the appliance will likely not operate at all, however, the fuse is designed to be easily replaceable. It is recommended to use insulated gloves and to avoid touching any exposed wiring connections. To replace the fuse, use a fuse puller to grip the metal caps and lift it out of the holder. Place the new fuse in the holder and ensure it is properly seated. Turn the appliance back on and check that the circuit is functioning.
This light bulb is for microwaves.
Light bulb illuminates the surface below the microwave or the interior of the microwave.
Because high-voltage capacitors in a microwave can retain a lethal electrical charge even when the microwave is unplugged, a service technician should install this part unless the owner's manual includes instructions for installing the light bulbs.
This microwave glass turntable tray provides a stable, rotating surface for even heating during cooking. Measuring approximately 13.5 inches in diameter, it is made from heat-resistant tempered glass for durability and safety. Designed to fit select microwave models, this tray helps ensure consistent results by allowing food to rotate smo...Read moreothly throughout the cycle. If your current tray is cracked, missing, or no longer turning properly, replacing it can restore optimal performance. Be sure to confirm compatibility with your microwave model before purchasing.
This OEM waveguide cover in your microwave is a heat-resistant component that prevents food, grease, and moisture from entering the waveguide. It is typically located on the side or top wall of the cooking chamber. If the cover is broken, you may notice cracks, charring, or burns, and potentially see arcing or sparks during operation. Not...Read more replacing a damaged cover can lead to short circuits and the risk of electrical components touching your food. To remove the cover, start by disconnecting the microwave from its power source before opening its door. The waveguide cover is slotted or snapped into place, so gently slide or apply pressure to release it from the clips or slots. Please note that the cover is sold individually.
This door switch is designed for use with various makes and models of microwaves and is a genuine OEM part. This individually sold switch connects to the frame of the microwave through the door switch holder, which will need to be removed completely in order to replace this switch. If your microwave will not start, displays error codes, o...Read morer if the door will not shut properly and the inner light stays on, the switch could have broken from use and is in need of replacement. Due to the high voltage used within the components of microwaves, take extra caution when repairing your microwave. To replace the door switch in your microwave, disconnect the microwave from the power, and use a flat-head screwdriver to gain access to the switch through the main control panel.
This coupler is a replacement mechanical component used to connect and transfer motion between internal assemblies. It is commonly replaced when wear causes slipping, noise, or loss of function.
Sold individually. This grease filter is for microwaves.
Grease filter traps grease from the exhaust air.
Follow the instructions in the owner's manual when installing this part.
This microwave door switch works with the door latch to control when the appliance can run, a worn switch may cause the microwave to lose power, fail to start, or trip a breaker, it fits select upper and lower switch locations, high voltage may remain inside the microwave after power is removed, use a trained technician for installation, confirm fit with the exact model number.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Robert - For model number 79080339310
March 4, 2022
I need a new handle (part 16), what screws do i buy with it (15?). Also, is it straight forward and safe for me to repair the door?
Hello Robert, thank you for writing. The screws are not sold on our site so you can reuse the original ones. The Handle is part PS8689603. To install you will need to remove the inside door panel with a putty knife or flat tool to lift off the inner frame to expose the screws that hold the handle in place. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you.
Hello Fred, thank you for your question. If the microwave shares a circuit with other appliances and runs at the same time as those appliances, they’ll quickly overload the circuit and trip the breaker. If you don’t have anything else plugged in it could be one of a few things. First, make sure there is no water inside around the turntable then you should check your door switches and capacitor. You can test your door switches with a multimeter. First, unplug your microwave. Some door switches have only two metal prongs extending from the body, while others have three. Those with three terminals will have a common (COM) terminal, a normally closed (N.C.) terminal, and a normally open (N.O.) terminal. Those switches with only two terminals will have either a common terminal and a normally open terminal, or a common terminal and a normally closed terminal. We are providing directions for testing a door switch with three terminals. If you are dealing with a door switch that has only two terminals, ignore the part of this test that does not apply to you. Using caution, remove all wiring harness leads from the switch's terminals. Use your ohmmeter to test your switch for continuity. Touch one meter lead to the COM terminal and the other lead to the N.O. terminal. Do not push in on the actuator. Your meter should give a reading of infinity, meaning the circuit is open, and there is no continuity. Without moving the meter's leads, press down on the actuator until you hear a 'click'. With the 'click' of the actuator, the meter should produce a resistance reading of zero ohms. This means the circuit is closed and continuity is present. (Switches with only two terminals do not 'click' when actuated) Keep the meter lead that is touching the COM terminal in place but move the other meter lead from the N.O. terminal to the N.C. terminal. You should receive a reading of infinity when you push in on the switch's actuator. When the actuator is released, you should receive a resistance reading of zero ohms. Now, set your ohmmeter to its highest resistance scale and touch one meter lead to the N.O. terminal and the other meter lead to the N.C. terminal. The resistance reading between these two leads should be infinite. Finally, take a resistance reading from both the N.C. terminal and the N.O. terminal to any metal mounting hardware that is a part of the switch assembly. You should receive a normal reading of infinity. Any readings that differ from the ones presented here are indicative of a defective door switch that will need to be replaced. Door switch part number PS12071303 and Switch part number PS12071302. You can also test the capacitor with a multi-meter. Make sure after unplugging your capacitor you release any electrical charge. You can do this with a screwdriver that has an insulated handle. When testing your capacitor set your meter to 1000 ohms. Touch your probes to the terminals on the part. If your meter stays on 0 then your capacitor needs to be replaced. Part Number PS12071296. We hope this helps. If you need help placing an order, our customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
How do I adjust settings to turn on sound when food is done
Hi Mike, thank you for reaching out. According to our research, press and hold the "2" button for 5 seconds. It should beep twice, and the sound will turn on. We hope this information helps!
Was this helpful?
Thank you for voting!
Mary - For model number 79080339310
April 7, 2023
When I close my door the panel will display the door not closed. I am not a professional but is it the seal that is around the door inside.
Hello Mary, Thank you for writing. If the Door is closed properly and is level and not lose, this could be an indication of the door switches is faulty and may need to be replaced. We hope this helps!
When we turn on the microwave, it’s all of a sudden blowing the fuse. It starts, but then immediately shuts off. Thank you for your help!
Hi Valerie, thank you for the question. Based on our understanding, we would recommend checking the high-voltage capacitor, part number PS12071313. It is an electronic device that holds a charge of electricity in the high-voltage circuit of the microwave. You may need to replace it to fix the issue. We hope this sorts out your problem!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Microwave tripped circuit breaker when turned on
40 of 67 peoplefound this instruction helpful.
Arthur from LUTZ, FL
Easy
15 - 30 mins
Screw drivers
Remove vent cover then remove touch screen control panel. When you remove control panel take photo of where everything is plugged in then unplug and remove control panel. 3 door switches located next to door in a plastic chassis. Test each switch with current tester. Remove the bad switch and replace with the new one. You tube DIY helped.
Was this helpful?
Thank you for voting!
Power would not come on, would trip breaker when connected.
18 of 28 peoplefound this instruction helpful.
JOSEPH from MIAMI, FL
Easy
15 - 30 mins
Screw drivers
First thing I dir was search YouTube for any related videos and found this one https://www.youtube.com/watch?v=uHj4H9Fdxrc, it was the exact problem my microwave was exhibiting. Once I verified the problem by troubleshooting, I removed the part and verified that the switches were working fine, the door latch assembly showed signs of wear
... Read morewhich was the cause of the problem. After receiving the replacement part I installed it, verified that power was restored to the unit and reassembled the microwave, works fine, hope it lasts a long time!
Read less
Was this helpful?
Thank you for voting!
Pressing the start, microwave will start and dies out. Electric is tripping.
11 of 18 peoplefound this instruction helpful.
ARNEL from WAUKEGAN, IL
Easy
15 - 30 mins
Screw drivers
The diagnosis is about an hour. Coz, I need to open the control panel, got a tester, and trsted all critical parts inside the panel. Also, replaced the fuse just to make sure its a new one. Found out it was a switch (bottom part) that control the open/close of the microwave door.
When found out the problem, the rest of t
... Read morehe work is easy.
My Orders
