7498VRV Magic Chef Range - Instructions

Remove racks and pull out stove from wall. Remove back cover from stove. Unscrew and unplug sensor. Rethread new sensor wire through hole and plug in new sensor and rescrew plate that holds in place.

We had complications because of how the stove was installed, which delayed the "fix" time considerably.

Also instal ... Read more led ignitor. It was determined that both were bad. Gas would come on but not light. When oven would light, it would not re-light periodically to keep the temperature up, causing gas smell. This added time to repair of an additional 1 hour, and required removal of bottom drawer.

SHUT OFF GAS
disconnect FLEX LINE from gas PIPE
remove GAS pipe from rear of stove
remove rear panel
remove pre-shaped gas lines to burners and oven / broiler
separate dual control valve from pressure regulator
disconnect wiring from dual control valve
REASSEMBLE in OPPOSITE order
turn on gas
... Read more />CHECK ALL FITTINGS FOR POSSIBLE LEAKS
Turn on each BURNER - making sure EACH one lites
turn on oven - making sure that the OVEN igniter lites the OVEN
set control on BROIL
turn on broiler - making sure that the BROILER
igniter lites the BROILER

Pulled the stove out from the wall. Removed the left side of the stove. Removed the wires from the old igniter. Modified four of the wire ends with the proper size spade connectors (supplied with the new part). Reinstalled the wires onto the new part. Tested the burners. Reinstalled the stove side. Moved the stove back into position.

Pulled off the oven door, just lift straight up. Pulled out the floor of the oven, very easy just lift from the back. The only problem I had was the screws holding the old igniter wouldn't come out, they just spun. I snipped them off and picked up two new ones at the hardware store. Pull the wiring harness in through the hole in the b ... Read more ack of the oven. Unsnap old wiring harness, snap in new one. Reattach the new igniter, replace floor, replace door. Turn on oven and cook food... fairly easy repair.

first of all i have one advantage even though i am 70 yrs old i had a appliance shop for sears in the 60s and 70s and have not forgotten to much of the basics i am still in the security business and up on electronics. last time i had the company repair the oven , 70 dollars for the part 75 dollars for the svs call. (first igniter was ... Read more on full warranty) well this time i decided to look for trhe part myself, i just went on line typed in oven repair parts and eventually all these sites came up. yours was the most professional looking and i took a chance. guess what everything you promised you delivered. price quality USA made parts and delivered in three days . opened package went to work less than fifteen minutes back in business.
will sure use you again if the need arises thank you

Pulled the oven away from wall to access rear of oven. Disconnect electric plug from duplex outlet, turn off gas supply ball valve. Removed two screws that retain sensor on inside of oven. Disconnected two prong sensor connector at rear of oven. Tied a length of string to sensor connector wires. Pulled old sensor out through front of oven ... Read more . Use the string to tie onto new sensor connector wires and pull new sensor into place from rear of oven. Retain sensor with two screws. At back of oven, used connector jumper supplied with part package to make connection to existing connector.

My front burners were inoperative because the metal gas lines under the cooktop were cracked. This happened because I tried to remove the cooktop without properly removing the screws holding the assembly to the cooktop. Doh!

Anyway, this is an easy fix. First, remove the 4 burner tops by rotating them counterclockwise and li ... Read more fting them out of the cooktop. Then, remove the two ignitor wires from each burner, and set the burners aside.

Next, remove the four small screws that hold the burner tube assemblies to the underside of the cooktop. There is one screw near each burner hole in the cooktop (the screws are covered when the burner tops are installed). You must remove all four screws even if you are only installing one replacement orifice and tube kit!

Now you can tilt the cooktop up and remove it from the stove, exposing the orifice and tube assemblies. Use an adjustable wrench to loosen the brass nuts connecting the gas tubes to the valves, and remove the assembly.

Reassemble in reverse order.

If you have "high speed" burners, remove the orifice that comes on the unit and replace it with the loose orifice that is in the packaging.

I first removed the bottom of the oven and the flame guide to uncover the igniter assembly. Then I applied WD40 to the two Philip head screws and unscrewed them to release the old igniter. The two wire leads from the igniter went into the back of the oven and I could not reach the connection block. So I pulled the oven out far enough to g ... Read more et behind it and took off the panel covering the electrical wires in back. I had previously disconnected the electrical cord from the wall outlet. After I determined that I could not remove the connection block I returned to the igniter and cut the two existing wires close to the ceramic igniter assembly. I marked the top wire with a Sharpie pen so that I would not mix up the new leads when I install the new igniter. Although it was awkward to work inside the small oven space I was able to strip the insulation back about 1/2 inch and then connect the new igniter wires using the twist caps supplied with the kit. I pushed the wires back into the space and added the insulating material supplied. The igniter assembly was then installed with the original two screws and the other oven covers and flame guide reinstalled easily. After reconnecting the power outlet the oven was back in operation with ignition of gas flame within a minute or so. It was a good feeling and now we do not need to consider replacing the gas range.

Look in the oven. On the upper left corner is the sensor. Remove two screws. Gently pull the wire and connector through the hole and insulation. Disconnect old sensor, replace new. Gently push the connection through, then finish pulling through from behind the stove. Replace the screws inside the oven. Done.

Range is 20+ year old 'condo issue' and difficult to pull from wall since previous owner had tiled it in. Going in from the back was going to be a pain.
Removed the oven door by opening slightly and pulling up. Removed grilles. Removed bottom of oven by sliding 2 latches in the back forward and pulling it up. Removed 2 screws hol ... Read more ding igniter (long-style) to the rear of the burner. Cut power to the range and snipped the 2 igniter wires as close to the igniter as possible, leaving me only about 1 inch of wire to work with. Removed 2 screws holding old plate to rear of the back of the interior of the oven. Snipped off the connector on the new igniter. Carefully stripped about 3/8" of insulation off of all wires and used hemostat to hold wires together while applying the wire nuts. Used hemostat to work the wire nuts and excess wire back into the hole. Stuffed the hole with supplied insulation. Attached new back plate with original screws and attached igniter to burner with original screws. Reapplied power to range and did a test light. It worked, so I reassembled the rest. For me, the worst part was holding the wires together so the wire nuts would 'take', while working inside of the oven. But, an easy and successful job!

A quarter turn counter-clockewise and the burner came out. Disconnect the old wires and connect the new wires. Place the burner in its place and a quarter turn clockwise and it was set.

1st removed the sealed burners
2nd removed stove top
3rd removed oven door
4th removed left and right side pannels to access door hinges
5th removed left and right hinges
6th installed new left and right hinges
then re-installed other components in reverse order.
The oven door now opens and closes proper ... Read more ly, the heat stays in the oven!!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then conected the new element and replaced te two screws. Turned on the oven & works fine.
Very Easy!

. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) pushed wires back in and secured sensor

Using the description on the first DIY, I did as told. All went well until the part about removing the panel to access the hinge. There isn't a "panel" on the side of this particular model of Magic Chef stove. You have to remove the entire side of the stove, and then, there's another panel inside of this one. That too has to come off. On ... Read more ce off, you're into the insulation surrounding the oven. Ain't pretty, I'll assure you. Then, the replacement hinge has holes in it for the mounting screws. The holes aren't threaded, and you have to replace the screws that come with the hinge with self-tapping screws. Either that, or thread the holes with a tap. Thank goodness my wife loves the stove, or it may have just gone out the door. This is not one of Magic Chefs better ideas. Either that, or they didn't plan on having to replace the hinge before the stove wore out.