7348B Frigidaire Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
No Heat, Dryer Runs, But Right Side Of Timer Would Not Advance, Left Timer Would
2 of 2 people
found this instruction helpful.
-
STEPHEN from Nashville, TN
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
I used the percentage scale on this website to try and determine the likely cause. After reading several sites, I couldn't make sense of the timer not working on just one type cycle. When I got the dryer drum off, I could plainly see that one of the heater coils was broken. They get heat stressed and break down over time and a hard shak
... Read more
e probably finished this off. This unit is 5 plus years old. It was Saturday and I had no heater, so I actually found it at a local parts supplier. Also replaced the drum bearing and the bearing cup in the rear along with the heater. BTW, a new heater comes with a HIGH thermal switch attached to it so don't buy it extra. The bearing cone also comes with a new bushing in the pack. I DID use the Thermal Limiter that I order from the site because I was already in there. Everything works great now. I may have gotten most off my parts elsewhere but this site was the biggest help of them all. I will definitely be back here again.
Read less
Was this helpful?
Thank you for voting!
The old drum seal top had torn off.
2 of 2 people
found this instruction helpful.
-
jeffrey from round lake heights, IL
- Easy
- 1- 2 hours
-
Screw drivers
Opened the drayer top and then removed the front panel.
Removed the bottom seal from the acr as it was warn.
Carefully scarped off the remaining bits of felt from the arc.
Applied the supplied adhesive to the top half of the cleaned arc.
Placed the seal and held in place with small spring clamps.
Let it dry for ... Read more an hour, then I repeated the process with the bottom seal.
I let it dry over night, overkill probably but I wanted it to stay.
Replaced the front with new seal and closed up the top.
It has been working well since. Thanks for stocking parts that help out homeowner's on tight budgets.
Removed the bottom seal from the acr as it was warn.
Carefully scarped off the remaining bits of felt from the arc.
Applied the supplied adhesive to the top half of the cleaned arc.
Placed the seal and held in place with small spring clamps.
Let it dry for ... Read more an hour, then I repeated the process with the bottom seal.
I let it dry over night, overkill probably but I wanted it to stay.
Replaced the front with new seal and closed up the top.
It has been working well since. Thanks for stocking parts that help out homeowner's on tight budgets.
Read less
Was this helpful?
Thank you for voting!
Lound noise inside dryer
3 of 5 people
found this instruction helpful.
-
Joseph from little Egg Harbour, NJ
- Easy
- 1- 2 hours
-
Screw drivers
1. unplug the dryer, remove the aluminum vent and move it to an area that has a lot of elbow room.
2. remove the top lid with a flat screwdriver. It seems that the top lid was being held by 2 metal clips on each end.
3. on the right hand side removed the 2 wires from the front face of the dryer. this is the switch for the ... Read more open door sensor. remember which wire goes where.
4. the on the left and right side will be one screw and one metal clip, unscrew and pop the front panel with a flat screwdriver.
5. in front of the drum remove the plastic clip that is used as a guide for the drum to be in place.
6. look in the drum and there is 3 screws that form a triangle shape. remove the screws.
7. remove the belt from the drum. inspect the belt. replace if necessary.
8. lift up and pull out the drum.
9. remove the rear drum assembly and replace it with the new parts.
10. repeat in reverse and your done.
It took me 40 minutes the first time i replaced the rear drum assembly then i forgot to hook the belt up correctly and i unassemble the unit in 5 minutes fix the belt and assemble the unit in 5 more minutes. Now the wife is happy.
2. remove the top lid with a flat screwdriver. It seems that the top lid was being held by 2 metal clips on each end.
3. on the right hand side removed the 2 wires from the front face of the dryer. this is the switch for the ... Read more open door sensor. remember which wire goes where.
4. the on the left and right side will be one screw and one metal clip, unscrew and pop the front panel with a flat screwdriver.
5. in front of the drum remove the plastic clip that is used as a guide for the drum to be in place.
6. look in the drum and there is 3 screws that form a triangle shape. remove the screws.
7. remove the belt from the drum. inspect the belt. replace if necessary.
8. lift up and pull out the drum.
9. remove the rear drum assembly and replace it with the new parts.
10. repeat in reverse and your done.
It took me 40 minutes the first time i replaced the rear drum assembly then i forgot to hook the belt up correctly and i unassemble the unit in 5 minutes fix the belt and assemble the unit in 5 more minutes. Now the wife is happy.
Read less
Was this helpful?
Thank you for voting!
Dryer making horrible squeaking sound when running
2 of 3 people
found this instruction helpful.
-
SHARON from SUMMERVILLE, SC
- Easy
- 1- 2 hours
-
Screw drivers, Socket set, Wrench set
I am a "do-it-yourselfer" despite my husbands opposition. I followed instructions from one of the posts on the site and took apart the dryer. I found the location of the rear bearing and took it out and replaced it with the new one. Easy as that. Made sure the parts looked the same. Made sure I saw how everything went together. I us
... Read more
ed a magnet to hold the ball bearing in place on the rear mount and taped the metal bracket on the outside of the dryer. Screwed it right in. Reassembled in reverse and works like a charm. To all the women out there who don't think they can do this. It's easy. Give it a try.
Read less
Was this helpful?
Thank you for voting!
bearing bad and shaft broken
3 of 6 people
found this instruction helpful.
-
Randall from New Roads, LA
- Easy
- 30 - 60 mins
-
Screw drivers
replaced bearing and shaft new belt and everything works just fine
Other Parts Used:
Was this helpful?
Thank you for voting!
Belt snapped after 13 yrs. maybe 15 yrs
2 of 3 people
found this instruction helpful.
-
JOHNNY from ASHEVILLE, NC
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver
I raised up the top then took 4 bolts out of the front and it came off and then I slipped the belt on. Now was the fun part. I tried to put belt around the tension spring from the front of the machine. Bad mistake. So I turned the machine around and took off little plate bottom left, back side reached in and WA-LA back in commision. I too
... Read more
k a long brush and cleaned all I could reach and put it back together. Bingo, back in business.
And I'm 71 yrs. old.
And I'm 71 yrs. old.
Read less
Was this helpful?
Thank you for voting!
Our door catch got lost inside the dryer after the door was slammed to hard
2 of 3 people
found this instruction helpful.
-
Joyce from PORTAL, GA
- Very Easy
- Less than 15 mins
I took the new door catch out of the packaging and just snapped it in place it was easy peasy and took less time than opening the package
Was this helpful?
Thank you for voting!
loud squeeling noise
2 of 3 people
found this instruction helpful.
-
Lewis from Thornton, CO
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
After changing the drum support bearing, and the front felt ring, the noise continued. It turned out to be the tensioner pully. The harmonic vibration travels throughout the dryer box like an instrument so you can't tell where the sound is comming from. Before you do anything, spray a little wd40 between the bushing and the shaft on th
... Read more
e belt tenioner pully. If the squeel goes away, you have found your smoking gun.
Read less
Was this helpful?
Thank you for voting!
Latch on dryer no longer worked
2 of 3 people
found this instruction helpful.
-
chris from dallas, TX
- Really Easy
- Less than 15 mins
So easy! I ordered the part on the website. Received it 24 hours later. And popped it in place. Good as new.
Was this helpful?
Thank you for voting!
lint screen was torn to No repair!
1 person
found this instruction helpful.
-
Ellsie from Rio Chiquito, NM
- Really Easy
- Less than 15 mins
-
Screw drivers
/removed the lint screen & tossed in the trash, removed one screw from each side of the frame with a screw driver. Placed the New frame in place
& secured it with the screws that I removed from the old frame, placed the screen in place & that was all there was to it. The total amount of time to remove the old & replace with the new ... Read more probably took 10-15 min. @ the most. I am so happy to have found the part & was able to replace it. You all are wonderful. Received it in 3 days, WOW!!
& secured it with the screws that I removed from the old frame, placed the screen in place & that was all there was to it. The total amount of time to remove the old & replace with the new ... Read more probably took 10-15 min. @ the most. I am so happy to have found the part & was able to replace it. You all are wonderful. Received it in 3 days, WOW!!
Read less
Was this helpful?
Thank you for voting!
Worn out lint screen
1 person
found this instruction helpful.
-
Vince from Grayslake, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
uncrew old, take out, put new in, screw in place.
Was this helpful?
Thank you for voting!
bearing went out
1 person
found this instruction helpful.
-
james from tahlequah, OK
- Really Easy
- Less than 15 mins
-
Screw drivers
took apart and replaced parts easy to do but no one in my town can get me parts. thay want 100.00 gust to come out and look at it so found parts online and thats that
Was this helpful?
Thank you for voting!
Broken lint screen
1 person
found this instruction helpful.
-
Mark from Elizabethtown, PA
- Really Easy
- Less than 15 mins
Lifted broken screen out and replaced it with a new one. Extremely simple.
Was this helpful?
Thank you for voting!
Drum was not revolving
1 person
found this instruction helpful.
-
khalid from HILLSBOROUGH, NJ
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
Open the back plate. Broken pulley was already out of place. Put the spring on the pulley and placed it. It took me less than 10 min
Was this helpful?
Thank you for voting!
broken belt and pulley
3 of 7 people
found this instruction helpful.
-
John from Temple City, CA
- Easy
- Less than 15 mins
-
Nutdriver, Pliers, Socket set, Wrench (Adjustable)
First of all, I've purchased a belt from local service center that cost me more than $21 (local tax is 8.5%). But, I can not find the idel pulley assembly so I searched on the Internet and ordered from PartSelect.com.
Surprisedly, my order came just one day - they must cross-ship from local distribution that it's even faster t ... Read more han to get those in local stores (driving .. and hope they have what I want ..).
I've replaced the belt 2 days ago - it's easy with 4 screws removed to pull out the front door. The back panel is opened with 2 screws remove, and very easy to replace the pulley.
It's a heavy duty gas dryer made in 1989 and this is the third time I changed the belt and the first time to change a new pulley. I would recommend to change the idle pulley because I may not need to change the belt if I have had replaced it last time. A broken or not functional idle pulley may damage the belt in a short time.
Appliance such as gas dryer like mine will last forever with replaceable belt and pulley. I'm really happy to see a working dryer (almost 20 years old) and my wife is asking a small component for her washer .. that I think I can easily fix that too .. with the help of PartSelect search.
Hope this will help.
John
Surprisedly, my order came just one day - they must cross-ship from local distribution that it's even faster t ... Read more han to get those in local stores (driving .. and hope they have what I want ..).
I've replaced the belt 2 days ago - it's easy with 4 screws removed to pull out the front door. The back panel is opened with 2 screws remove, and very easy to replace the pulley.
It's a heavy duty gas dryer made in 1989 and this is the third time I changed the belt and the first time to change a new pulley. I would recommend to change the idle pulley because I may not need to change the belt if I have had replaced it last time. A broken or not functional idle pulley may damage the belt in a short time.
Appliance such as gas dryer like mine will last forever with replaceable belt and pulley. I'm really happy to see a working dryer (almost 20 years old) and my wife is asking a small component for her washer .. that I think I can easily fix that too .. with the help of PartSelect search.
Hope this will help.
John
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!