EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

7348B Frigidaire Dryer - Instructions

All Instructions for the 7348B
46 - 60 of 278

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Lint screen had torn
3 of 3 people found this instruction helpful.
  • Luann from Huntersville, NC
  • Really Easy
  • Less than 15 mins
For me it wasn't even a repair, but rather, open the package, take out and discard the old lint tray and pop the new one in! Done. I didn't have to replace the frame. I would like to comment on how easy ordering was from partselect.com and how quickly the part arrived. Very satisfied customer! Thank you!
Was this helpful?
Thank you for voting!
Needed new lint screen for dryer
3 of 4 people found this instruction helpful.
  • Harriett from Leesburg, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed 2 screws and dropped new screen holder in with lint screen in it and replaced screws. Really easy
Was this helpful?
Thank you for voting!
Dryer wouldn't spin, belt broken
3 of 4 people found this instruction helpful.
  • Reveice E from Arcadia, FL
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Popped the top of the dryer off. Removed 3 screws from lower front panel. Removed front panel slide belt over drum, remove 2 bolts from rear panel and installed belt over motor and around idler tensioner. Reinstalled front panel and top of dryer . Also greased idler pulley to shaft , beings tensioner was okay. Plugged in and tested dryer , it was okay.
We went to PartSelect. com and order the belt and it was fast shipping. We couldn't find the belt anywhere else. Thanks for PartSelect.
Was this helpful?
Thank you for voting!
Dryer not heating
2 of 2 people found this instruction helpful.
  • Steve from COVINGTON, KY
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
UNPLUG DRYER (this is key) Removed the top of dryer. used screwdriver and pliers to remove two screws and electrical connections then reinstalled new part stick the magnet behind the part to the back of the dryer to help control the small screws.
Was this helpful?
Thank you for voting!
Dryer would not turn on, no power. Since i already have replaced thermal limiter switch, i knew exactly what to do and also how to shorten installation
2 of 2 people found this instruction helpful.
  • Daniel from SAN ANTONIO, TX
  • Very Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Remove 2 screws from back of unit, remove top by lifting and pulling up, set aside. Using pliers,needle-nose, remove the 2 wires from switch, then using a magitized philips screw driver, remove 2 screws holding switch to back of unit, replace switch, reassemble everything. 20 minutes, boom, ur done, dry some clothes now
Was this helpful?
Thank you for voting!
Dryer drum would not turn
3 of 5 people found this instruction helpful.
  • Ben from Weaverville, NC
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
I first removed a vent cover in the back where the idler is located. With pliers I removed the tension off the spring. Next I simply slide the idler off the post. I pulled up on the top panel which opened like a clam shell. I used a flat blade screw driver to separate the front panel from the dryer so I could slide the new belt around the drum. I reversed the steps. All in all it was easy. It took me about 30min including cleanup.
Was this helpful?
Thank you for voting!
May not have to take out the whole drum to replace the limiter!
2 of 2 people found this instruction helpful.
  • Timothy from CRANBURY, NJ
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
After lifting the dryer top and finding the location of the thermal limiter on the back of the dryer, where it is difficult to get at, I carefully cut through the dryer cabinet with the multimaster on three sides to form a 'flap' upon which the limiter was mounted. By prying this flap open from the back, the two wires and two screws are e asily accessible to replace the limiter, without having to remove the whole drum. Afterwards, I just bent the flap back into place and taped the seams. If it ever blows again, the fix will take all of about two minutes.
Was this helpful?
Thank you for voting!
Riped lint screen
3 of 5 people found this instruction helpful.
  • Bill from Shelby, MI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
This was easer than, well brushing my teeth. And it took less time than that too. Really, really easy, just like I read.
Was this helpful?
Thank you for voting!
The lint screen was old, rusty, and torn.
2 of 2 people found this instruction helpful.
  • Paul from Dennis, MA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
This was the easiest and most inexpensive repair I ever had on a dryer. I did a search on the internet, found "PartSelect.com" searched their web site, found the part I needed (at a very reasonably low price) ordered it, received it within 2 days, opened the box, removed 2 screws from the old part, put the new part in, replaced the 2 scre ws, inserted the filter screen... and my wife was happy. Thank You PartSelect.com for perfect selection, ordering and service.
Was this helpful?
Thank you for voting!
screen fell out of lint screan frame
2 of 2 people found this instruction helpful.
  • steve from scottsville, KY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
remove 2 screws,pull frame out. put new in. tighten 2 screws. put lint screen in
Was this helpful?
Thank you for voting!
Door catch broken
2 of 2 people found this instruction helpful.
  • TJ from SCOTT DEPOT, WV
  • Very Easy
  • Less than 15 mins
Popped in the new door catch! Tightened the hinge screws( which work loose and allow the door to droop. The reason the catch broke!) Also put red Loctite on the screws in an attempt to keep them from backing out again! Working great so far!!!
Was this helpful?
Thank you for voting!
replace old screen
2 of 2 people found this instruction helpful.
  • charles from nantucket, MA
  • Really Easy
  • Less than 15 mins
take out of box remove old screen drop in new screen
Was this helpful?
Thank you for voting!
Wire Meshing Had Broken Away From The Rubber Framing Tha Was To Hold It Together And Lint Was Bypassing The Screen And Getting Into The Vent Tube.
2 of 2 people found this instruction helpful.
  • JOHN from NAUGATUCK, CT
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Opened the dryer door unsrewed the two phillips holding the filter framework in place did a two second swap-out dropped the new unit into place the new unit and refastened it with the 2 screws that held the old one in place . And was drying a load of clothes within two minutes . . Thank you jg
Was this helpful?
Thank you for voting!
dryer lint screen rplacement
2 of 2 people found this instruction helpful.
  • Frank from Las Vegas, NV
  • Really Easy
  • Less than 15 mins
  • Screw drivers
removed two screws - replaced lint screen replacement, TIME TO REPLACE UNIT - ONE MINUTE. What made this project a snap was the pictures and graphs( parts replace) uses to ensure you are ordering the exact screen .
Was this helpful?
Thank you for voting!
Lound noise inside dryer
3 of 5 people found this instruction helpful.
  • Joseph from little Egg Harbour, NJ
  • Easy
  • 1- 2 hours
  • Screw drivers
1. unplug the dryer, remove the aluminum vent and move it to an area that has a lot of elbow room.
2. remove the top lid with a flat screwdriver. It seems that the top lid was being held by 2 metal clips on each end.
3. on the right hand side removed the 2 wires from the front face of the dryer. this is the switch for the open door sensor. remember which wire goes where.
4. the on the left and right side will be one screw and one metal clip, unscrew and pop the front panel with a flat screwdriver.
5. in front of the drum remove the plastic clip that is used as a guide for the drum to be in place.
6. look in the drum and there is 3 screws that form a triangle shape. remove the screws.
7. remove the belt from the drum. inspect the belt. replace if necessary.
8. lift up and pull out the drum.
9. remove the rear drum assembly and replace it with the new parts.
10. repeat in reverse and your done.
It took me 40 minutes the first time i replaced the rear drum assembly then i forgot to hook the belt up correctly and i unassemble the unit in 5 minutes fix the belt and assemble the unit in 5 more minutes. Now the wife is happy.
Was this helpful?
Thank you for voting!
All Instructions for the 7348B
46 - 60 of 278