65002 - Instructions

Removed micro bottom - 5 screws. One screw on the motor and a clip. Reversed the sequence, turned it on and watched it turn.

Switched the refrigerator circuit breaker to off. Put tape around the switch to prevent scratches. Wedged the putty knife into the right side of the switch and pried up.the switch and connector popped out. Removed the connector from the old switch and connected it to the socket in the new switch. Stuffed the new switch and connector back ... Read more into its home. Switched on the circuit breaker. Now we have light in the refrigerator with every opening!

I followed the directions! It was so easy that I bought another switch for my sister's fridge (same as mine). Her light was out too!

Unplugged the refrigerator, Taped around the edges of switch as I had read to prevent possible scratches, used very thin flathead screwdriver to pry out old switch, unplugged old switch, plugged in new switch, put it back in opening, plugged fridge back in, and I had beautiful light! Hardest part was unplugging the refrigerator!

Unplugged the refrigerator. Used small flat head screw driver to push the front tab of the old switch in and pulled it out with pliers. Detached and reattached the wires to the switch. Reinserted back into hole. Plugged refrigerator back in to power. All good.

The old switch was a little hard to get out....took me a couple tries. I couldn’t move the frig out to unplug it, so just shut the power off in the kitchen. But, I was happy that’s what the problem was and so happy to have the light back on......it was probably three years it didn’t work!

Remove 2 Philips Head screws on left side of microwave. Remove 3 Philips Head screws from bottom rear of microwave. Remove 4 security screws from back of microwave (holding the cover to frame). These are the security type tips that are like a Torx bit, but need to be hollow in middle to accommodate pin in center of screw. Then back pl ... Read more ate of microwave with heavy transformer still attached slides up and away. The wires aren't long enough to allow it to rest flat on the bench, but weight is low so it's easy to hold it upright while removing the motor unit. Separate connector from motor (simple) Remove motor by unscrewing 1 phillips head screw and rotating counter-clockwise a tiny bit. Remove Motor. Reverse steps to re-assemble. Note that there are a series of tabs at the bottom of the back cover that fit into holes in the baseplate of microwave. It can be a little tricky to line them up with the weight of the transformer, but it's not too bad. Once lined up, it drops in nicely and all the various screw holes line up. The microwave is a bad cooker when the plate doesn't spin. This simple and inexpensive fix saved me from having to buy a whole new oven.

Removed the MW from the wall. Took the top screws off the air vent. Then removed the two screws holding on the display. I then moved the display to its side and it revealed the micro switches. I removed the plug in leads from the micro switch one at a time. I did this with all three micro switches only one at a time. I reinstalled everyth ... Read more ing and plugged it in. No more fans starting when the door is opened.

Used a screwdriver to remove covers. Used a blow dryer to defrost coil in freezer. Cut zip tie and removed old controller assembly. Inserted new controller assembly and secured with zip tie. It took 24 hours for the fridge to cool completely. Now it works fine.

pried out old switch, disconnected wires ,placed wires on new switch

Used a screwdriver to take off broken clip and then used same screwdriver to replace with new clip. Very easy.

Pulled fridge away from wall, unplug electrical connection, open fridge door, use knife to prize out door switch, pull off and replace switch from electrical wiring.

I had previously watched a YouTube video (do this first!!) on a similar Kenmore model so I knew what to look out for: (1) turned off power, (2) took thin putty knife to slip under outer lip of switch (most screwdrivers are too thick), (3) wiggled switch at front end to release the tab, (4) unplugged from the socket, (5) plugged in new sw ... Read more itch, (6) popped new switch back into door, (7) turned on power. Voila !! Super easy. I couldn't believe it.

Unplug the microwave. Remove the Philips head and safety Torx head screws along the bottom of the sides and rear of the microwave which hold the black cover on. Lift the cover up at the rear and slide it backwards to disengage the tabs on the front top. Remove the cover. Discharge the capacitor by shorting the terminals to each other ... Read more and then ground. Do this with a well insulated object and be aware there may be a pop when you do this. Keep hands, etc. on the insulated part of the object (screwdriver handle, etc). There's a lot of stored energy in that capacitor. I'd advise first checking the diode to make sure its not bad. Replace it if it is. The Magnatron is held in with a couple of screws on the top and sides. Unplug the connector and remove the screws. Remove the Magnatron. Installation is the reverse of removal.

Removed outer cover

removed lower door switch

installed new switch

Wa La!