The interior light in your refrigerator is controlled by a switch that is activated when the door is opened and closed. If your refrigerator light will not turn on, or stays on when the door is closed, you could have a faulty switch. The switch is spring-loaded and is a generally closed type of switch meaning there should be no continuity...Read more when the button is pushed, and continuity through the switch when it is no longer engaged. This plastic, white, OEM switch is sourced directly from the manufacturer, is sold individually and is easy to replace. The repair usually takes less than 15 minutes and requires a flat-blade screwdriver and needle-nose pliers.
This micro-switch is designed for use in your microwave. The function of this part is to monitor the door latch position and communicate to the electronic control board whether the latch is open or closed. If your microwave does not provide heat, or will not start properly, you may need to replace the micro-switch. This part is approximat...Read moreely 1 inch in length and 3/4-inch in width. It is made of black plastic with two metal prongs. This is an OEM part sourced directly from the manufacturer. This part is sold individually. Be sure to disconnect the microwave from the power source before you begin this repair.
The door switch, often referred to as a primary interlock switch, provides power to the various components in the microwave when the door is in a closed position, and interrupts power when the door is open. This door switch is approximately 1 1/2 inches long, and has 2 metal prongs called terminals that extend from its body. Common sympto...Read morems related to a faulty primary door switch include: microwave will not turn/shut off, or the microwave will not heat properly. You can check the switch for continuity using a multi-meter. With the actuator button depressed, you should see continuity between these terminals. If there is no continuity the switch will need to be replaced.
NOTE: Before you begin this repair, first make sure your microwave is unplugged, and that your capacitor is discharged. A capacitor stores large amounts of electricity even when your microwave is unplugged.
This refrigerator door hinge bushing is a durable white plastic component that provides a smooth pivot point for the hinge pin, helping keep the door properly aligned and sealed. It is commonly used to correct doors that sag, make noise, or are difficult to open or close due to a worn or damaged bushing. The bushing installs at the door h...Read moreinge pivot point and typically requires removing the hinge bracket with a 10?mm socket. Color is white, and size and dimensions may vary by refrigerator model.
The fuse-time delay may also be known as a line fuse or a microwave fuse, and it is a piece for your microwave. The function of this part is to shut off the microwave if there is a power surge, in order to protect your microwave from damage. You should consider having a service technician install this part as the high-voltage capacitors i...Read moren a microwave can contain a very harmful electrical charge, even when the microwave is unplugged and has been inactive for some time. The tools that would be needed to complete this installation include a Phillips screwdriver, an insulated screwdriver, and a pair of pliers.
This lower holder cover is also known as a toe grille clip, or a kickplate clip. It is designed for use with refrigerators. The main purpose of this part is to hold the molding at the base of your refrigerator in place, it also makes removing the piece of molding simple. If you notice that the kickplate on your appliance is loose or will ...Read morenot stay in place you may need to replace one or more of these clips. This part is made of plastic, and it is sold individually.
This AC synchronous motor is a genuine OEM replacement part specially made for microwaves. It operates on an alternating current, and it is responsible for rotating the turntable to ensure even heating of your food. The motor can fail due to physical damage or malfunctioning internal components such as the bearings. If your turntable is n...Read moreot rotating, you will need to replace the motor. You can find it underneath the microwave cavity, near the center. Disconnect the microwave from the power source and remove the cover. Turn the microwave over and remove the bottom panel to access the motor. Disconnect the motor from its mounting location, and then insert the new motor in its place. Ensure the new motor is securely attached before reassembling the appliance.
This compressor start relay and thermistor assembly helps start the refrigerator's compressor and protects it from overheating during operation. It provides the electrical boost needed to get the compressor running, which is essential for maintaining proper cooling inside the refrigerator. If the refrigerator is not cooling properly, the ...Read morecompressor is not starting, or you hear repeated clicking noises, a faulty relay assembly may be the cause. Replacing this part can help restore reliable compressor operation and keep the refrigerator cooling as intended.
This part is a replacement light socket for your refrigerator. This model is white in color, and it has two sockets that will fit two separate light bulbs. The light socket connects to the power source, and the light bulb is screwed into it. If the light in your refrigerator is not working when you open the door, you could have a faulty s...Read moreocket. It is important to determine if the light bulbs are simply burned out, or if the socket is causing the issue. Be sure to disconnect your refrigerator from the power source before you begin this repair. This is an OEM part sourced directly from the manufacturer.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Microwave would not rotate or heat up food.
52 of 77 peoplefound this instruction helpful.
Joshua from WHITE LAKE, MI
Very Easy
15 - 30 mins
Screw drivers
After watching a few youtube videos, I used a phillips SD to take controll pannel off to access the switches that sense when microwave door is closed. Swapped out all 3 switched and mocrowave works like new. $20 fix (shipping included)
My 8 year old daughter cleaned the inside of the microwave with enough water to rival a tsunami. Resulted in a clean microwave with a fried out motor that no longer revolved. Part came quickly. Took cover and bottom off to get to the part. One screw held it on and a plug. Removed those, put on new part and she was good to go. No tri
... Read morep to home depot today.
Read less
Was this helpful?
Thank you for voting!
Remove and replace light switch
45 of 90 peoplefound this instruction helpful.
Debbie from Waltham, MA
A Bit Difficult
30 - 60 mins
Pliers, Screw drivers
Video makes it look easy. Kenmore refrigerator does not have "groove" along the right hand side of switch that allows for pushing down on release. Used a thin screwdriver to get under to push while holding switch edge with pliers. Kept slipping. Tape sides to avoid scratching inside of refrigerator.