6161 - Parts

This is an authentic Milwaukee replacement part, sourced from the original manufacturer for use with angle grinders. The special flange is used to seal the area above the inner flange and the spindle assembly. This special flange is available as an individual replacement part, please see model diagram for associative parts.

This authentic Milwaukee component is supplied by the original manufacturer for angle grinders. This is a complete spindle hub assembly that includes all the gears, bearings, and the housing. It is an important part of the tool which helps to drive the main shaft. Over time components may wear out, get damaged or lost eventually requiring...Read more replacements. Check the diagrams for your model to ensure the correct repair procedure. Note, this high-quality spindle hub assembly is made of durable metal and is sold individually. A wrench set and a screwdriver might be needed to replace this assembly.

This replacement armature assembly is an authentic component which is supplied by the original equipment manufacturer for use with Milwaukee angle grinders. It is a complete assembly which includes an armature, a plastic fan, and the armature bearing. Due to constant contact with carbon brushes armature will eventually wear out and will n...Read moreeed to be replaced, it is highly recommended to replace both carbon brushes when replacing an armature. Plese note this high-quality item is sold individually.

This authentic component is supplied directly from the original equipment manufacturer for use with Milwaukee angle grinders. A field is an electromagnet utilized to generate a magnetic field in an electric motor. It provides an identical replacement for a missing or a faulty assembly that was installed on a new unit. Please make sure to ...Read morerefer to the owners manual and the appropriate diagrams of your model for the correct location and application of this part. Keep in mind this high-quality field assembly is made of durable metals and is sold individually.

Genuine Milwaukee replacement part Includes two Carbon Brushes with wire lead,Brush Spring & Brush Holder. • Worn brushes frequently are the cause behind a motor running poorly. • Replacing brushes can fix a motor that's operating intermittently. • New brushes can restore a motor's electric braking. Carbon brushes are one of ...Read morethe most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

This is an authentic manufacturer approved replacement item. It is commonly used on Milwaukee angle grinders. This sealed metal bearing helps to secure armature while allowing it to spin freely. Includes one (1) bearing per order. To complete this repair you would need a screwdriver and pliers. • Remove the side handle • Remove the...Read more guard • Remove the handle • Separate the grinder • Disengage the brushes • Remove the fan • Remove the gear case • Remove the armature • Remove the pinion gear • Remove the front bearing • Install the new bearing • Reassemble unit and test it

It is an authentic item sourced directly from original equipment manufacturer. It is generally used on Milwaukee angle grinders. This bearing helps to support armature and allows it to spin freely. Over time because of pressure and heat ball bearings will wear out and need to be replaced. Please note this sealed metal bearing is sold indi...Read morevidually. Replacing this ball bearing is a relatively easy task. You would need a screwdriver, pliers and a rubber mallet to complete this repair. • Make sure the tool is unplugged. • Remove the side handle. • Remove the guard. • Remove the handle. • Separate the grinder. • Disengage the brushes. • Remove the fan. • Remove the gear case. • Remove the armature. • Remove the pinion gear. • Remove the front bearing. • Install the new bearing. • Reassemble and test the unit.

This genuine manufacturer sourced replacement hardware that is made for use with Milwaukee power tools. It is a standard hex nut that has multiple applications depending on the model of your tool, please make sure to check appropriate diagrams for correct location and use of this item. This nut is made from durable, high quality metal and it is sold individually.

This replacement screw is a high quality item that is sourced directly from original equipment manufacturer. It is a genuine Milwaukee hardware commonly utilized on sanders, grinders and handheld cut-off machines. This is the screw for the switch. Please note, one torx screw is included per order.