613H - Parts

This is an OEM replacement part and is sold individually. Its propose is to deliver an electric current from an ignition system to the combustion chamber of a gas fueled engine. It will ignite the air fuel mixture by the spark. Spark Plugs will usually have to gapped to the manufactures specifications found in the owners manual. Over tim...Read moree a Spark Plug will become fouled because the air/fuel ratio may be set wrong,worn piston rings, carbon build up and other factors. It is better to replace a fouled spark plug, rather then trying to clean it.

This oven door seal is fifteen and a half inches long. It is made of rubber and has a metal hook on either end to hold it in place. This seal sits on top of the glass window pane.

This ball bearing is sourced from the original equipment manufacturer and can be used in a variety of outdoor equipment. It has an inner diameter of 11/16 inches. The ball bearing provides support for the rotating parts in your equipment and reduces the amount of friction they are subject to during use. If the bearing is not adequately lu...Read morebricated or has worn down, you may hear grinding or squeaking from your equipment and notice excessive vibration when in use. It is important to address this issue promptly as a faulty ball bearing can potentially damage the parts located near it. To replace the ball bearing, use a pry bar or bearing puller to pry it out of its housing. Clean the housing thoroughly and press your new ball bearing in position. Note that when pressing the ball bearing into place, apply force only to the outer portion of the bearing.

This Fuel Filter is a white plastic part attached within the fuel delivery system between the fuel tank and carburetor. Installation is rated as "Easy" and requires a set of pliers and a screwdriver. If broken, there may be a leak or blockage and the part should be replaced. The part may also need to be replaced according to manufacturer'...Read mores specifications, and is a manufacturer-approved part. Refer to your make, model and diagrams to ensure this part is correct.

This Ball Bearing is an individually sold, silver/black, metal part. It reduces friction in the spindle assembly between the spindle shaft and the spindle housing. If broken due to wear/fatigue, you will hear a grinding, growling, rumbling or screeching sound, and should replace the part. Refer to your make, model and diagrams to ensure this is the right part for you.

It is a genuine item that is supplied by the original equipment manufacturer for Briggs and Stratton engines commonly installed on a variety of lawn and garden equipment. This is a special component that provides a tight seal for the PTO side of the crankcase. Over time it may wear out and begin to crack eventually requiring a replacement...Read more. Check the appropriate diagrams for your specific model to ensure the correct installation of the new seal-oil. To perform this repair you will need a variety of tools such as a screwdriver, a wrench set, pliers and a tool to pick out the old seal. Make sure to drain the oil before starting this repair. Keep in mind, one durable rubber part is included.

Sold as a kit, including the metal body switch, a pair of keys, and the required hardware, this Ignition Switch Assembly has been sourced directly from the original manufacturer. If you are unable to start and stop your engine, you may need to replace the Ignition Switch Assembly. To complete this repair, you will need a screwdriver, a wrench set, and pliers. Customers rate this repair as Easy.

This OEM approved overhaul kit is designed for rebuilding/fixing carburetor on a Briggs and Stratton engine. This kit contains all the necessary gaskets, diaphragms and other parts to rebuild your carburetor. It helps to fix common problems associated with worn out gaskets or diaphragms, including leaks and sluggish performance and other related issues. Replacing these items you would need a screwdriver and pliers.

This genuine manufacturer supplied overhaul kit is designed for rebuilding carburetor on a Briggs and Stratton engine. This kit contains all the necessary gaskets, diaphragms and other parts to rebuild your carburetor. It is used to fix common problems associated with worn out gaskets or diaphragms. Replacing these items you would need a screwdriver and pliers.

This starter motor is for lawn and garden equipment engines. Starter motor spins the flywheel to start the engine. Wear work gloves to protect your hands when installing this part.

It is a genuine item that is supplied directly from the original equipment manufacturer for use with Murray, Snapper and Simplicity lawn mowers. This is an identical replacement for a missing or damaged housing-arbor top that was originally installed on a new unit, please make sure to check the appropriate diagrams and the owners manual f...Read moreor the correct location and application of this component. Keep in mind this high-quality item is made of durable metal and is sold individually.