605222850A Frigidaire Dishwasher - Parts

This grey OEM dishwasher tub gasket is a 73" grey rubber part that creates a seal around the dishwasher to prevent any water leakage during a cycle. If it's damaged or broken, you'll start seeing water leaking out. If broken, it should be replaced. Refer to your model number and user manual to ensure this part is right for you. When makin...Read moreg this repair, open the dishwasher door and take out the lower dish tray for better access. Pull out the old gasket, and clean the channel with a rag. Push the new gasket into place into the notch on the door, which you should see upon close inspection, using a flat-head screwdriver for assistance if necessary. We do not recommend cutting any additional length off on the tub gasket if any is present during your repair.

The heating element nut is used to connect the heating element to the dishwasher tub. If water is leaking from underneath your dishwasher, you may need to tighten or replace the heating element nut. Replacing the nut is an easy job, does not require any specialty tools, and should not take you more than 10 minutes. For our step by step gu...Read moreide, click the video below. The brass nut measures 7 inches in length x 1 inch in width x 5 inches in height, and fits most dishwashers. To see if this part is compatible with your dishwasher, check the list of compatible brands below.

If your dishwasher is leaking or not draining properly, you may need to replace the drain hose. The drain hose connects to the pump located below the lower spray arm and aids in proper dishwasher drainage. This white and black plastic hose is 7.5 feet long. For this repair, you will need either a 1/4-inch or 5/16-inch nut driver, dependin...Read moreg on your model. You will need to remove the lower access panel on your dishwasher to complete this repair; it is often easier to remove the dishwasher from the cabinet to do so. Be sure to disconnect the dishwasher from both the power and water supply before completing this repair.

This dishwasher door latch assembly is a critical component designed to ensure safe and efficient operation. It features an integrated switch that functions as an on-off mechanism, preventing the appliance from running when the door is open. If your dishwasher fails to start or the door does not close or latch securely, replacing the latc...Read moreh assembly may resolve the issue. Installation requires disconnecting the power supply to avoid electrical hazards. This part is compatible with standard dishwasher models and is engineered for a secure fit and reliable performance.

This is a drain pump assembly for various compatible models of dishwashers, that is responsible for draining the water from the dishwasher after every cycle. This drain pump assembly is made of plastic and fits within the sump assembly, which controls the flow of water into the drain. This drain pump assembly is a genuine OEM part and is ...Read moremade of a high-quality plastic but is sold as an individual component without any other parts, like its drain pump check ball which works within the pump to prevent water from backwashing into the pump, as well as the drain pump cover. If you notice your dishwasher is not draining or has a lot of water buildup at the bottom of the sump assembly, this filter may be damaged, clogged or broken, and in need of a replacement. To replace this pump assembly, you will only need a Philips-head screwdriver, but should start by removing your dishwasher racks. Then, pull up on the lower spray arm, and drain trap to remove them. Next, rotate the spray arm support and pull that up to remove it, at which point you can remove the base and filter for the drain pump. With those out, you can use your Philips-head screwdriver to disconnect and remove the cover and drain pump assembly. With the pump removed, you can inspect it or install the new drain pump assembly, with the same hardware as before. Then it is as simple as reassembling the rest of your dishwasher, ensuring each connection point is fastened tightly.

This plastic cover and stem assembly helps hold the lower spray arm in place.

Sold individually.

This dishwasher heating element is a genuine replacement component designed to maintain optimal water temperature during the wash cycle and assist in drying dishes at the end of the cycle. Positioned at the bottom of the dishwasher tub, it ensures efficient cleaning and drying performance. Compatible with a wide range of models from Frigi...Read moredaire, Kenmore, Crosley, Electrolux, and other related brands, this element replaces older versions and restores proper function when symptoms such as poor cleaning, inadequate drying, or water leaks occur. Installation requires disconnecting power to the appliance to ensure safety. Sold individually.

Sold individually.

Sold individually.

The tubing carries water from the water inlet valve to the tub.

This kickplate grille is attached to the bottom of the dishwasher.