4804 - Instructions

Pulled stove away from wall and unplug .Removed grates for better access. Unscewed element scews removed element & tested for continuity.there was none element is bad . Replaced with new one . Time about 20 minutes.

Originally I had anticipated a major problem requiring the removal of the back of the range and perhaps the necessity of employing the services of a repairman ($$!). Fortunately I waited for the arrival of the replacement element, which, upon inspection, was not configured to go through to the back of the range. What a relief!

... Read more The hardest part of the repair was finding the correct nutdriver (5/16"). Removal of the damaged element was simply backing out the two retaining screws inside the oven and pulling the element out far enough to expose the clips to the wire. Pulling them apart was easy enough, and then the element I disposed of immediately.

Reverse of removal of the old element was the installation of the new: Reconnect the clips to the element, push the wires back into the insulation, re-inserting the two retaining screws and tightening them gently.

The final step was to plug the range 220 cord into the outlet. Testing whether the element was functional was a breeze; the oven and the range elements worked perfectly.

Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely.
Once all was replaced and reinstalled the oven ... Read more has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.

Just took the old one out & put the new one in . Just a few screws to remove & put them back when replacing to new broil element , and were back up and cooking :)

Turned off power to stove;removed baking racks , loosened Holden screws to pushon bake element removed old bake element,installed new pushon bake element.

Removed the back panel, disconnected the terminals and removed the old one and installed the new one.

Unplugged the stove first !
Removed bake element ; (2 screws), looked OK,
measured with an Ohm meter, measured "open".
Also, removed rear cover (6-screws), wires not burnt. Ordered new element-rec'd next day! My wife installed it and replaced rear cover. Works great (oven!) and about $10 cheaper and quicker than from ... Read more a local dealer!

First we turned off the electic, then we took the back off the stove and pulled the wire off the bad element then replace the new element. It was very easy to do.

I unplugged the damaged element and plugged in the new one. It took less trhan 30 seconds and the unit worked just fine.

Very simple. Removed oven rack that had melted residue on it and replaced it with the new one from your company. I want to tell you that the delivery service I received was just geat. Took less than 48 hours to arrive at my home from the time I placed the order on line. Keep up the good work and I will be happy to share my experience ... Read more with those in need of you services. Thanks. Marilyn Kasson

It took me more time to find the right tool then to remove and replace the element. If I can do it anybody can do it. Removed two (2) screws with a nutdriver. Detached the element replaced with new element and replaced screws. Easy job!

I removed the baking racks then unscrewed the default screws for the baking element.I then disconnected the electrical leads from the damaged element. I then removed the old damaged baking element and installed the new baking element, attaching the electrical leads after cheking for weak spots in the element. I then re installed the bakin ... Read more g racks and started the oven to burn off any factory oils on the baking element.

Pretty easy installation; you lift the top plate up and snip the wires maybe four inches away from the burner. Leave more wire than you think you need; once you get into it you'll realize you need more wire length than you think.

Then strip the remaining ends, twist them together with the provided caps, and use the heat shrink ... Read more to hold it together. Remove the old terminal, replace it with the new ones, and you're good to go!

Remember to check that the wires are tight in the cap before heat shrinking, though. I had to get more shrink wrap in order to finish.

First thing I did was turn off power to the range at the circuit breaker. The repair was generally easy with the exception that 1 screw holding the broiler element support was "welded" into the oven ceiling. I stripped the screw trying to get it out. Fortunately, I had a special tool that allows one to grip the outer edge of the screw w ... Read more hile turning it --- and that's how I got it apart. Once the broiler element support was off, I removed 2 screws holding the broiler element itself to the oven wall and carefully pulled the broiler element out from the oven wall and detached the wire clips connecting the wires to the broiler element. I reattached the clips onto the new element and installed the new element back into the oven wall. I then reattached the broiler element support using a another screw (because I decimated the original one). I then turned the circuit breaker back on and turned the broiler on. Woila. My broiler works again! Special thanks to the people at this site who were very helpful in seeing to it I got the correct broiler element. The original ordered broiler element was delivered to the wrong address. The folks at this site sent me another one. To make a long story short, they saw to it I got the correct part. I highly recommend this site based on my experience with them.

Drank a beer, grabbed a screwdriver & tried to remove the two screws that held the element in place. The screws were old and when I turned them, they stripped instantly. This required another beer. Eventually I used pliers to grip the sides of the screws to remove and reinsrt them. When I finished the oven worked great, so I celebrated wi ... Read more th another beer.