463241 Char-Broil Grill - Overview

Genuine Char-Broil replacement part, this item is sold individually. It includes the igniter and two 26

This is a Genuine OEM replacement part designed for use with Char-Broil Grills. It is a Caster socket insert for rectangular Steel Tube Legs. This part is made out of Plastic and it is Sold Individually. To attach this Socket to a unit use a Bolt and a Nut (Not Included) to secure it to the Metal Leg of a Cart Side Panel. Then, simply bolt in the bottom of the Socket.

OEM Rolled Stainless Steel Emitter is sold individually. This is the emitter tray only designed to be paired with a cast iron cooking grate part 80021355. Dimensions are approx. 18-1/4 X 8-7/8" Part is 5/8" Thick. If the part is heavily rusted or damaged it needs to be replaced.

This is a genuine Char-Broil replacement part, it is sold individually. This is the part of the Grill that the flame is coming from on your Gas Grill. Depending on your grill you may have 3 or 4 of these. To connect these to your grill, place the flat side of the Burner in the rear side of the firebox in the slots provided. The front of t...Read morehe burner will connect to the Electrode W/ Wire/Collector. They will connect to the Hose Valve Regulator, and then the Control Knobs will be attached, so the flame can be controlled. This part includes one threaded pin and one cotter pins.

This flame tamer also known as heat tent is a genuine manufacturer approved replacement part. It is sourced directly from original manufacturer for use with gas grills. Heat tents help to direct grease and drippings away from the burner tubes. This will help to reduce flare ups tremendously. Grill parts will rust in combination of heat an...Read mored moisture, that is why it is important to clean the grill after each use. Includes one (1) metal flame tamer per order. No tools needed to replace.

This genuine manufacturer sourced replacement part is specially designed for Char-Broil grills. Igniter is the part that produces the spark to ignite the burner. Features 2 input terminals and two (2) output-connector on the back for the ignition switch. Requires a AA battery (not included). Replacing this electronic ignition module is ...Read moreeasy and does not require any tools • Unplug the wires from the old ignition module • Remove old igniter and replace it with a new one from the kit • Unscrew the button that holds module to the unit • Secure new module in place • Install a battery and secure the module with the button • Connect the wires and test the unit

This is an Original Char-Broil replacement parts used for some of their Grills. This part is made out of Metal and it is Sold Individually. The purpose of bars is to direct grease and drippings away from the burner tubes, which cuts down on flare ups tremendously. An extra benefit of Flavorizer Bars is that they help add that "cooked on a...Read more grill" flavor to your food. Bars rust is the combination of heat and moisture and should be replaced of they are damaged our have holes. No tools are required to replace this Flame Tamer, simply place it in the Bracket over the Burner.

This is an adjustable burner bracket designed for use with Char-Broil grills. It contains stainless carryover channels. Adjusts 23-1/2" to 25". Includes 2 bar extensions, 2 angled extensions for brackets ending at an angle, hardware and instructions. Fits burners up to 2-5/8" wide. You would need a screwdriver to complete this repair.

This is a Genuine Manufacturer Approved Control Knob used on Char-Broil Gas Grills. It helps to control your Burners. This part is made out of Plastic and it is Sold Individually. Replacing this part does not require any tools, this Knob fits over the Regulator Shaft. Please note Bezel is Sold Separately.

This is an authentic Char-Broil replacement part. The cleaning tool is found in grills. This part is made of metal, and is an accessory used to scrape debris off of the infra-red emitter. No tools are required when replacing this item. This part is sold individually.

This is a genuine OEM replacement part for a Char-Broil Outdoor Stove. The grease tray is designed to catch grease drippings from food as it cooks. Before replacing this part make sure the stove is completely cooled down to avoid any possible injury. This part is made of metal with a grey powder coat finish. It is a separately sold replacement part.

This replacement grease cup is specially designed for use with Char-Broil grills. It is an authentic item that is sourced directly from original equipment manufacturer. The purpose of this tray is to collect the grease and other food particles from the food you are cooking. After each use it is recommended to clean this part with soap and...Read more water to avoid rusting. This item is made out of metal and it is sold individually. Please note, the grease cup clip/holder is sold separately.