463241113 Char-Broil Grill - Overview

Genuine Char-Broil replacement part, this item is sold individually. It includes the igniter and two 26

This is a genuine Char-Broil replacement part, it is sold individually. This is the part of the Grill that the flame is coming from on your Gas Grill. Depending on your grill you may have 3 or 4 of these. To connect these to your grill, place the flat side of the Burner in the rear side of the firebox in the slots provided. The front of t...Read morehe burner will connect to the Electrode W/ Wire/Collector. They will connect to the Hose Valve Regulator, and then the Control Knobs will be attached, so the flame can be controlled. This part includes one threaded pin and one cotter pins.

This is an Original Char-Broil replacement parts used for some of their Grills. This part is made out of Metal and it is Sold Individually. The purpose of bars is to direct grease and drippings away from the burner tubes, which cuts down on flare ups tremendously. An extra benefit of Flavorizer Bars is that they help add that "cooked on a...Read more grill" flavor to your food. Bars rust is the combination of heat and moisture and should be replaced of they are damaged our have holes. No tools are required to replace this Flame Tamer, simply place it in the Bracket over the Burner.

This is a Genuine Manufacturer Approved Control Knob used on Char-Broil Gas Grills. It helps to control your Burners. This part is made out of Plastic and it is Sold Individually. Replacing this part does not require any tools, this Knob fits over the Regulator Shaft. Please note Bezel is Sold Separately.

This is a genuine OEM replacement part for a Char-Broil Outdoor Stove. The grease tray is designed to catch grease drippings from food as it cooks. Before replacing this part make sure the stove is completely cooled down to avoid any possible injury. This part is made of metal with a grey powder coat finish. It is a separately sold replacement part.

This is a manufacturer approved replacement part designed for use with Char-Broil gas grills. This item is made out of metal and it is sold individually. The carryover tube provides support for the burners, and carries the flame from one burner to the next. They also help to secure the burners in place. Over time, your carryover tubes may...Read more rust or warp. This would be the time to replace them. This assembly includes two (2) cotter pins.

This thermometer/ temperature gauge is a genuine manufacturer sourced replacement part. It is specially designed for use with Char-Broil grills. It can be used to measure temperature inside the grill. This part is made out metal and it is sold individually. It does include a wingnut that helps to secure it to the unit. Dial reads 150 - 650 degrees. No tools would be needed to replace this item.

This cooking grate is an authentic Char-Broil replacement part. It is compatible with multiple models of Char-Broil grills. This cooking grate provides a surface to place meat and other items of food for cooking on. It is made of a durable metal, and it should be replaced if it is beginning to rust or is past the point of being able to clean it. This part is sold individually, and it requires no tools to install

This locking caster is sourced from the original equipment manufacturer for use with outdoor grills. It consists of a wheel, with a diameter of 3 inches, and a metal bracket that allows for easy transportation and positioning. It also includes a locking mechanism that prevents unintentional movement of the grill. Over time, the caster may...Read more break, corrode, or fall out of alignment, thereby causing instability, failure of the locking system, and potential accidents. The caster will also need to be replaced if it is jammed or stripped. To replace a defective caster, prop the grill up and use a wrench or screwdriver to turn and remove the caster mounting bolt. Remove any dirt and debris in the area and align the new caster with the mounting hole. Turn the caster until it is firmly locked in place to complete the repair.

This is an OEM part sourced directly from the manufacturer. The warming rack is found in Char-Broil grills. This part is made of metal, and is used to hold food higher above the heating element in the grill. No tools are required when replacing this item. Simply remove the old part and slot the new one into place. This item is sold individually.